What Is an H Buffer? H1 3.8 oz AR-15 Buffer in 3D
The H buffer, also sold as H1, weighs 3.8 ounces: one tungsten weight and two steel. Watch it slow the bolt carrier in 3D, cut open to see the weights slide, and compare it with the carbine, H2 and H3.
Quick answer
- The H (or H1) buffer: one tungsten weight and two steel, 3.8 oz. The mil-spec answer for a 14.5" or 16" carbine gas barrel.
- It's the usual pick for 14.5" and 16" carbine gas rifles, and most rifles as a first try.
- In this tool's model a tuned 16" carbine gas rifle with the h buffer throws brass to about 3:30, and to about 2:30 with a suppressor.
Source: buffer maker specifications; brass positions from this tool's cycle model.
Watch the h buffer cycle, in 3D
Press play, or tap a step. Drag to turn it, pinch to zoom, and cut it open to see the carrier, the buffer's weights and the spring. Change the gas or add a can and watch where the brass goes.
H buffer, 3.8 ozTuned · 1000x slower
The bullet passes the gas port. Gas runs back down the gas tube, through the carrier key into the chamber behind the bolt's gas rings, and drives the carrier rearward while the bolt stays locked.
Like a 16" carbine gas barrel.
A can's back pressure pushes the carrier harder.
TunedTuned. Brass lands at 3:30, the carrier cycles fully and stops gently. Leave it alone.
Brass lands at
3:30
3 to 4 is tuned
Carrier speed
15.9 ft/s
modeled, as the gas lets go
Back of the tube
Taps
0.4 J left at impact
One cycle
75 ms
about 790 rounds a minute on full auto
A teaching model, not a measurement: one push of gas, a mil-spec carbine spring, an 11.5 oz carrier group. Real rifles vary with the barrel, the ammo and the spring. Get a starting buffer for your barrel
H buffers in stock
Ranked by what builders add most, in stock first. One listing per model.
What does a buffer do in an AR-15?
When a round fires, gas tapped from the barrel runs back down the gas tube, through the bolt carrier's key and into a small chamber behind the bolt's gas rings, and shoves the carrier rearward. The carrier unlocks the bolt, pulls the empty case out and throws it. The buffer rides against the back of the carrier the whole time, so the two travel back into the tube together against the buffer spring.
The buffer adds its mass to the carrier's. Its weight sets how fast the carrier moves: heavier is slower, so it unlocks a touch later, throws brass further back and hits the back of the tube softer. The spring stores the push and sends everything home, stripping the next round off the magazine and locking the bolt.
The weights inside slide. When the carrier slams shut they keep moving forward and land a moment later, which stops the carrier bouncing back off the barrel extension. That's what the "Lock" step shows in the cutaway.
AR-15 buffer weights: carbine, H, H2 and H3
Carbine, H, H2 and H3 are the same length and fit any carbine tube; only the weights inside change. Silver is steel, dark is tungsten.
| Buffer | Weight | Weights inside | Usually runs in |
|---|---|---|---|
| Carbine buffer | 3.0 oz | 3 steel | 16" mid-length and intermediate gas rifles, and rifles that run a little soft |
| H buffer | 3.8 oz | 1 tungsten, 2 steel | 14.5" and 16" carbine gas rifles, and most rifles as a first try |
| H2 buffer | 4.6 oz | 2 tungsten, 1 steel | Short barrels on pistol or carbine gas, suppressed rifles and forced reset triggers |
| H3 buffer | 5.4 oz | 3 tungsten | Suppressed short barrels and heavily overgassed rifles |
Not sure where to start? The buffer weight calculator gives a starting weight from your gas system, barrel length, tube, ammo and muzzle.
How do I know if my buffer is too light or too heavy?
Read the brass. Fire ten rounds and look where the cases land, with 12 o'clock at the muzzle.
| What you see | What it means | What to do |
|---|---|---|
| Brass at 1 to 2 o'clock, dented cases, sharp recoil | Overgassed. The carrier is moving too fast. | Go one buffer step heavier, or close an adjustable gas block. |
| Brass at 3 to 4 o'clock, consistent pile | Tuned. Leave it alone. | None. |
| Brass at 5 to 6 o'clock, weak ejection, no lock back on empty | Undergassed or overbuffered. | Go one step lighter, check the gas block alignment and gas key screws. |
| Runs fine suppressed, short strokes unsuppressed | Buffer is set for the can. | Adjustable gas block, or accept a lighter buffer and more gas to the face suppressed. |
Carbine vs rifle buffer system
A collapsible stock rides a carbine tube, which takes the short carbine buffer family and the carbine spring. A fixed A2 style stock covers a longer rifle tube with a longer, heavier buffer and a longer spring. The longer rifle spring isn't squeezed as hard over the stroke and the heavier buffer slows the carrier, so the push back is smoother.
The parts don't mix: a rifle buffer won't fit a carbine tube, and a carbine buffer and spring in a rifle tube won't cycle right. The A5 system sits between them, a carbine style tube 0.75 inches longer that takes a rifle spring and its own A5 buffers.
Frequently Asked Questions
What is the difference between an H and an H1 buffer?
None. H and H1 are two names for the same 3.8 ounce buffer with one tungsten weight and two steel weights.
Is an H buffer good for a 16 inch carbine gas AR-15?
Yes, it's the usual starting point. A 16 inch barrel with a carbine length gas system runs a little hot, and the H's extra 0.8 ounces over a carbine buffer brings ejection back to about 3 to 4 o'clock.
H buffer or H2?
Start at H. Go to H2 if brass still lands at 1 or 2 o'clock, if you add a suppressor, or if you run a forced reset or binary trigger (check the trigger maker's instructions).
How does an AR-15 buffer system work?
Gas from the barrel pushes the bolt carrier back. The carrier unlocks the bolt, extracts and ejects the case, then pushes the buffer back into the buffer tube, compressing the buffer spring. The spring then drives the buffer and carrier forward, the bolt strips a new round off the magazine, chambers it and locks.
What does a heavier buffer do?
It slows the bolt carrier. Brass lands further back (toward 4 o'clock), recoil feels softer, the carrier hits the back of the tube less hard and the cyclic rate drops. Too heavy for the gas the rifle has and it short strokes: weak ejection and no lock back on an empty magazine.
What are H, H2 and H3 buffers?
Heavier versions of the 3.0 ounce carbine buffer, all the same length. Each swaps one of the three steel weights inside for tungsten: H (or H1) 3.8 oz with one tungsten weight, H2 4.6 oz with two, H3 5.4 oz with three.
Why are there loose weights inside a buffer?
So the carrier doesn't bounce. When the carrier slams forward into battery, the weights inside the buffer keep moving and hit a moment later, pushing the carrier back into battery instead of letting it rebound. The cutaway shows them slide.
Does the buffer spring matter as much as the buffer?
Yes. A worn carbine spring lets the carrier run back faster and returns it weaker. A carbine spring has 37 to 39 coils; replace it when it's clearly shorter than a new one beside it, or when the rifle starts acting gassy. Flat wire and extra power springs change the timing like a heavier buffer does.
Can I put any buffer in any buffer tube?
No. Carbine, H, H2 and H3 fit carbine tubes. Rifle buffers fit rifle tubes. A5 buffers fit A5 tubes. Each tube takes its own spring.
Is the 3D cycle a real measurement?
No, it's a teaching model: one push of gas against a mil-spec carrier, buffer and spring, tuned so a 16 inch carbine gas rifle with an H buffer throws brass to about 3:30 and cycles at a rate inside the M4's published 700 to 970 rounds a minute. Its carrier speeds and impact numbers are modeled, not measured. It shows which way each change moves things, not the exact numbers for your rifle.
Cite this tool: GunPartPicker, “What Is an H Buffer? H1 3.8 oz AR-15 Buffer in 3D”, https://gunpartpicker.net/tools/ar-15-buffer-system/h-buffer. Buffer weights from maker specifications; the cycle is a teaching model. Free to cite with attribution.
Read next
All guides →
More Gun Tools
- TuningBuffer Weight CalculatorEnter your gas system, barrel length, buffer tube and ammo, add a suppressor or a fast trigger, and get the buffer weight to start with plus the buffers in stock that match.
- LegalSBR Planner (3D)Set the barrel anywhere from 7.5 to 16 inches, put a stock, a brace or a folder on the back, pin a muzzle device or slide on a can. The ruler under the rifle shows whether you've cleared the 16 inch barrel line and the 26 inch overall line. Pick your state for its SBR, suppressor and assault weapon rules, then price every part and open the build in one click.
- CompatibilityFRT and Binary Trigger PickerChoose your platform and see every forced reset trigger, binary trigger and Super Safety the catalog carries for it, what the host needs to run one, and where each is in stock.
- LegalGun Travel CheckerCan I bring my gun to another state? Pick where you start, where you are going and what is coming along: carry pistol, AR-15, magazines, suppressor, SBR, brace, forced reset or binary trigger, hollow points. Every state on the route is checked for transporting firearms across state lines: magazine limits, assault weapon bans, NFA rules, carry permit type and trigger bans, with what to do before the state line.
- PlanningAR Build Cost CalculatorHow much does it cost to build an AR-15? Pick caliber, barrel length, stock or brace and optic, then drag both edges of the price band from the cheap end to the top end. Every slot fills with the part builders add most that is in stock, priced live. The headline total is the core rifle, optics and extras are priced separately, and beside them sits what builders really pay per slot, measured from real part picks. Roll a random build, or open yours in the builder in one click. Computed from over 1 million AR parts selected on GunPartPicker since 2020.
- CompatibilityMuzzle Thread CheckerPick your barrel's caliber and platform, get the standard thread pitch, and see every muzzle device and suppressor in the catalog that actually threads on, with live prices.
- CompatibilitySuppressor Mounts (3D)Put a can on its mount in 3D. Compare SilencerCo ASR, Dead Air KeyMo, SureFire Fast-Attach, HUXWRX QD, HUB 1.375x24 and direct thread: what goes on the barrel, what is on the can, how it locks and which cans fit which mounts. Cut it open to see the taper and the baffles, then shop the mounts and cans in stock.
- CompatibilityDI vs Piston (3D)Watch a direct impingement AR-15 and a gas piston HK416 fire in slow motion x-ray 3D. Follow the gas from the port back into the carrier, or into a piston that kicks an op rod, see which bolt runs hot, and compare weight, cleaning, suppressed use, carrier tilt and cost.
- CompatibilityGlock Red Dot Fit CheckerPick how your Glock slide is cut and see which red dots mount directly, which need a plate, and the plates and optics in stock right now.
- CompatibilityGlock Size ComparisonPick any two Glocks and see them to scale as real photos sized to Glock's published dimensions, side by side, from behind and as an X-ray, with the difference in length, height, width and weight in one line and the pistols in stock for each.
- CompatibilityP385 Size ComparisonSee the SIG P385 CARRY, COMP and FULL to scale against the P365-XMACRO, the P320 and the Glock 19, 17, 45 and 43X, as real photos sized to the published length and height, with every dimension and where to order one.
- Paint plannerGun Paint PlannerRattle can guns online before you spray. Paint, stencil and camo a real photo of about 1,800 guns: AR-15s, AR-10s, AR-9s, AKs, every Glock, pistols, shotguns and bolt action rifles, the way the rattlecanned guns on r/rattlecannedguns are done, with Krylon, Rust-Oleum, Aluma-Hyde, DuraCoat and Cerakote colors, then get the cans to buy in spray order.
- TuningTwist Rate CalculatorPick a bullet and a twist rate, get the Miller stability factor, then see barrels with that twist and ammo loaded with that bullet, with today's price per round.
- TuningOptic Zero (3D)See where a 25, 36, 50, 100 or 200 yard zero hits on a 3D range, with your ammo, barrel length and optic height. Compare two zeros side by side, look through your red dot, EOTech or LPVO at each distance, then tap where your group hit and get the exact clicks up, down, left and right for your optic.
- LegalBarrel and Overall Length CheckerEnter barrel length, muzzle device and how the back end is configured, and see whether the build is a rifle, a short barreled rifle, a pistol or an AOW under federal law, with the barrels in stock at that length.
- PlanningNight VisionLook around a real 360 degree scene through Gen 1, Gen 2+, Gen 3 green and white phosphor tubes, digital night vision and thermal. Turn the moon down from full to overcast, switch on an IR light, compare two devices side by side. Or walk a 3D farm at night and spot the people, hogs and deer hiding in it. Then see the PVS-14, PVS-31, GPNVG-18 and the thermal scopes people buy, with prices.