Ballistic Gel Test in 3D: 5.56 and .300 Blackout by Barrel Length and Distance
Fire M193, M855, 77 gr OTM, .300 Blackout 110 gr TAC-TX or 220 gr subsonic into a block of ballistic gel in 3D, from a 10.3 to 20 inch barrel at 10 to 300 yards. Watch the bullet yaw, break up or open in slow motion, see the stretch cavity and the wound it leaves, how deep it goes against the FBI's 12 to 18 inches, and how far out your barrel keeps 5.56 fast enough to fragment.
Quick answer
- M193 and M855 break up in gel when they hit faster than about 2,700 fps. From a 16" barrel M193 stays that fast out to about 90 yd; from a 10.3" only to about 25 yd.
- A 77 gr open tip match bullet breaks up down to about 2,100 fps, so from a 10.3" barrel it still does at about 170 yd.
- .300 BLK 220 gr subsonic match ammo doesn't expand: it went 24" on a straight track in a published test, past the FBI's 12 to 18".
Source: Fackler's 2,700 fps fragmentation threshold; Roberts (NDIA 2008) for 77 gr OTM; Shooting Illustrated (2013) for 220 gr subsonic; GPP's G1 flight model for speed at distance.
Shoot 5.56 and .300 BLK into ballistic gel in 3D
Pick the ammo, your barrel and how far away the gel is, then fire. The bullet hits a 16 inch block of 10% ordnance gelatin in slow motion: watch it yaw, break up, open or tumble, the stretch balloon and snap back, and the wound track it leaves, with a ruler and the FBI's 12 to 18 inch window on the bench.
Loading the 3D view
M193 · 16" · 50 ydFragments · 2,854 fps at the block · slow motion
3,050 fps at the muzzle from 16".
995 ft-lb at the block.
FragmentsHits at 2,854 fps, over the 2,700 fps it needs. Yaws about 4.7" in, snaps at the cannelure and throws lead and jacket fragments out of the stretch; the base piece keeps going to about 14".
Speed at the gel
2,854 fps
needs 2,700 to break up
Neck (yaws at)
4.7"
the narrow start of the wound
Penetration
14"
inside the FBI's 12 to 18"
Breaks up out to, 16"
about 90 yd
over 2,700 fps at the target
Bare 10% gel, rounded. Depths from published shots (Fackler's M193 wound profile and 2,700 fps fragmentation threshold). The stretch is drawn to scale with the energy, not measured. Real shots vary. What barrel length costs you
Cheapest M193 in stock today: $0.50 a round (Frontier Cartridge FR200 Frontier 5.56 NATO Ammunition, M193, 55 GR Full Metal Jacket, Brass, Boxer, Reloadable - 500 Round Case)
How far does 5.56 fragment from each barrel?
The distance out to which the load still hits at or over the speed it needs to break up, by barrel length. Sea level, standard air, no wind; the load figures are chronograph averages, so your rifle may differ by a few yards either way.
| Load | Needs | 10.3" | 11.5" | 14.5" | 16" | 20" |
|---|---|---|---|---|---|---|
| 5.56 M193 55 gr FMJ | 2,700 fps | 25 yd | 40 yd | 75 yd | 90 yd | 135 yd |
| 5.56 M855 62 gr green tip | 2,700 fps | None | 15 yd | 70 yd | 95 yd | 165 yd |
| 5.56 77 gr OTM (Mk 262 type) | 2,100 fps | 170 yd | 185 yd | 225 yd | 245 yd | 290 yd |
"None" means it leaves the barrel already under the line. M855 from a 10.3" (2,687 fps) is the classic case.
What a gel block shows: neck, stretch and permanent wound
The neck is the first few inches, where the bullet goes in point first and leaves a track barely wider than itself. A long neck means the bullet does little until it is deep; a short one means it starts to work right away.
The stretch, or temporary cavity, is the gel thrown outward as the bullet yaws or opens and then snapping back, all in a few thousandths of a second. In gel it shows as cracks; in tissue, stretchy muscle shrugs off much of it, while fragments flying out through it cut the stretched tissue and turn it into lasting damage. That is why fragmentation matters for small, fast 5.56 bullets.
The permanent wound is the track left after the stretch closes: what the bullet and its fragments actually cut or crushed. The FBI wants the main piece to reach at least 12 inches and ideally not past 18, deep enough to get to vital organs from a bad angle or through an arm.
Gel is a repeatable stand-in for soft tissue, calibrated with a steel BB, so loads can be compared. It has no bone, skin or organs, so read it as how a load behaves, not as a prediction of any one shot.
M193 vs M855 vs 77 gr OTM in gel
M193 (55 gr FMJ) is the classic: about 4.7" in it yaws, snaps at its cannelure and sprays lead and jacket fragments, with the base running to about 14". It needs about 2,700 fps to do that, which it has from a 16" barrel to about 90 yd and from a 10.3" to about 25 yd. More in the M193 vs M855 vs M855A1 guide.
M855 (62 gr green tip) needs the same 2,700 fps but is less consistent: its steel penetrator makes it nose-heavy in an odd way, so when it starts to yaw depends on how it was yawing as it hit, as early as 1 to 2" or as late as 7 to 8". Under 2,700 fps from a short barrel it can pass through like an ice pick.
77 gr OTM (the Mk 262 type) leaves the barrel slower, but its long open tip bullet turns almost at once and breaks up down to about 2,100 fps. In the published Federal 77 gr shot the neck was 0.5", the widest stretch 4.5" across at 4.5" deep, and it went 16.75". It is the load to pick for a short barrel.
.300 Blackout in gel: supersonic vs subsonic
.300 BLK is a .30 caliber bullet, too slow to fragment like 5.56, so it works by expanding. A solid copper 110 gr Barnes TAC-TX at about 2,200 fps from a 9" barrel opens into petals in the first inch, keeps nearly all its weight and runs a few inches past 18".
Subsonic 220 gr match (OTM) loads are built to be quiet, not to open: at about 975 fps the match tip doesn't expand, and in Shooting Illustrated's test they went 24" on a straight track. For hunting or defense with a subsonic load, pick one built to expand at 1,000 fps. Compare short barrel options in the 300 Blackout vs 5.56 guide.
Bullet speed at the target, by barrel and distance
Feet per second at each distance, from the same flight model the tool uses.
| Load and barrel | Muzzle | 50 yd | 100 yd | 200 yd | 300 yd |
|---|---|---|---|---|---|
| M193 10.3" | 2,794 fps | 2,608 | 2,432 | 2,099 | 1,793 |
| M193 11.5" | 2,848 fps | 2,660 | 2,482 | 2,145 | 1,835 |
| M193 14.5" | 2,983 fps | 2,789 | 2,606 | 2,259 | 1,940 |
| M193 16" | 3,050 fps | 2,854 | 2,667 | 2,316 | 1,992 |
| M193 20" | 3,230 fps | 3,026 | 2,831 | 2,467 | 2,131 |
| M855 10.3" | 2,687 fps | 2,541 | 2,399 | 2,129 | 1,877 |
| M855 11.5" | 2,753 fps | 2,604 | 2,461 | 2,187 | 1,931 |
| M855 14.5" | 2,918 fps | 2,764 | 2,615 | 2,331 | 2,066 |
| M855 16" | 3,000 fps | 2,843 | 2,691 | 2,403 | 2,133 |
| M855 20" | 3,220 fps | 3,054 | 2,896 | 2,594 | 2,313 |
| 77 gr OTM 10.3" | 2,479 fps | 2,365 | 2,253 | 2,039 | 1,838 |
| 77 gr OTM 11.5" | 2,515 fps | 2,399 | 2,287 | 2,071 | 1,867 |
| 77 gr OTM 14.5" | 2,605 fps | 2,487 | 2,372 | 2,152 | 1,944 |
| 77 gr OTM 16" | 2,650 fps | 2,531 | 2,415 | 2,193 | 1,982 |
| 77 gr OTM 20" | 2,770 fps | 2,648 | 2,529 | 2,300 | 2,084 |
| BLK 110 9" | 2,200 fps | 2,063 | 1,931 | 1,685 | 1,465 |
| BLK 110 10.5" | 2,238 fps | 2,099 | 1,966 | 1,717 | 1,493 |
| BLK 110 16" | 2,375 fps | 2,231 | 2,093 | 1,833 | 1,597 |
| BLK 220 sub 9" | 975 fps | 960 | 946 | 919 | 895 |
| BLK 220 sub 10.5" | 983 fps | 967 | 953 | 926 | 901 |
| BLK 220 sub 16" | 1,010 fps | 993 | 976 | 947 | 920 |
Muzzle speeds are 16" chronograph averages moved a flat amount per inch of barrel, the same as the optic zero tool, so the two agree.
Where the gel numbers come from
- 5.56 M193 55 gr FMJ: Fackler's M193 wound profile and 2,700 fps fragmentation threshold.
- 5.56 M855 62 gr green tip: 2,700 fps threshold (Fackler); neck spread of 1 to 8" with yaw at impact (JSWB-IPT, via Roberts).
- 5.56 77 gr OTM (Mk 262 type): Federal 77 gr Tactical OTM at 2,677 fps (Roberts, NDIA 2008); ~2,100 fps threshold as commonly cited for Mk 262.
- .300 BLK 110 gr Barnes TAC-TX: Barnes (expands within the first inch, petals to about twice the diameter); GearScout 2012 bare gel weights and depth.
- .300 BLK 220 gr subsonic OTM: Federal and Remington 220 gr OTM: no expansion, 24" straight track (Richard Mann, Shooting Illustrated, 2013).
- Below a load's threshold the depths are this tool's estimate (a later yaw, no fragments, deeper), and the stretch cavity is drawn to scale with the energy, not measured. The tool says so on each shot.
Frequently Asked Questions
How fast does 5.56 need to be going to fragment?
About 2,700 fps at impact for M193 and M855, the figure from Dr. Martin Fackler's wound ballistics work. From about 2,500 to 2,700 fps they break up some of the time, and under 2,500 they generally stay in one piece. Heavy open tip match bullets like 77 gr Mk 262 types break up down to about 2,100 fps, some tests 1,900.
How far does M193 fragment from a 16 inch barrel?
In this tool's flight model, M193 at about 3,050 fps from a 16 inch barrel stays over 2,700 fps out to about 90 yards. From a 14.5 inch it is about 75 yards, from an 11.5 inch about 40, and from a 10.3 inch about 25. A 20 inch barrel stretches it to about 135.
Why is M855 called an ice pick?
M855 was designed to punch through a steel helmet at long range, not to break up in soft targets. When it hits nearly straight it can go 7 to 8 inches before it starts to yaw, and under 2,700 fps it often doesn't break apart at all, leaving a narrow wound. When it hits yawing it can turn in 1 to 2 inches, which is why gel results with M855 vary so much shot to shot.
Is 77 grain better than 55 grain from a short barrel?
For breaking up in tissue, usually yes. A 77 gr open tip match bullet leaves a 10.3 or 11.5 inch barrel slower than M193, but it needs only about 2,100 fps to break up instead of 2,700, and it holds its speed better. In this tool's model it breaks up out to about 170 yards from a 10.3 inch barrel, where M193 stops at about 25.
Does 300 Blackout subsonic expand in gel?
Most 220 gr subsonic match (OTM) loads don't. In Shooting Illustrated's test the Federal and Remington 220 gr OTM did not expand and went 24 inches on a straight track. Subsonic loads built to expand, with soft hollow points or petals made to open at about 1,000 fps, are the ones to use on game or for defense.
What is the FBI 12 to 18 inch penetration standard?
The FBI's ammunition test protocol wants a bullet to go at least 12 inches in 10% ordnance gelatin and ideally no more than 18, deep enough to reach vital organs from any angle and through arms, without much spare to exit. Rifle bullets that break up early can still reach 12 inches with their base piece; deep, narrow tracks like a 220 gr subsonic OTM go well past 18.
Is ballistic gel the same as a person?
No. Calibrated 10% gelatin is a repeatable stand-in for soft tissue that lets tests be compared, not a model of a body: there's no bone, no skin and no organs of different density. Use it to compare loads and see how speed changes what a bullet does, not to predict a single shot.
Cite this tool: GunPartPicker, “Ballistic Gel Test in 3D: 5.56 and .300 Blackout by Barrel Length and Distance”, https://gunpartpicker.net/tools/ballistic-gel-test. Gel figures from published bare 10% gelatin tests, rounded; speed at distance from the optic zero tool's G1 model Free to cite with attribution.
Read next
All guides →More Gun Tools
- LegalBarrel and Overall Length CheckerEnter barrel length, muzzle device and how the back end is configured, and see whether the build is a rifle, a short barreled rifle, a pistol or an AOW under federal law, with the barrels in stock at that length.
- TuningOptic Zero (3D)See where a 25, 36, 50, 100 or 200 yard zero hits on a 3D range, with your ammo, barrel length and optic height. Compare two zeros side by side, look through your red dot, EOTech or LPVO at each distance, then tap where your group hit and get the exact clicks up, down, left and right for your optic.
- LegalSBR Planner (3D)Set the barrel anywhere from 7.5 to 16 inches, put a stock, a brace or a folder on the back, pin a muzzle device or slide on a can. The ruler under the rifle shows whether you've cleared the 16 inch barrel line and the 26 inch overall line. Pick your state for its SBR, suppressor and assault weapon rules, then price every part and open the build in one click.
- TuningTwist Rate CalculatorPick a bullet and a twist rate, get the Miller stability factor, then see barrels with that twist and ammo loaded with that bullet, with today's price per round.
- LegalGun Travel CheckerCan I bring my gun to another state? Pick where you start, where you are going and what is coming along: carry pistol, AR-15, magazines, suppressor, SBR, brace, forced reset or binary trigger, hollow points. Every state on the route is checked for transporting firearms across state lines: magazine limits, assault weapon bans, NFA rules, carry permit type and trigger bans, with what to do before the state line.
- PlanningAR Build Cost CalculatorHow much does it cost to build an AR-15? Pick caliber, barrel length, stock or brace and optic, then drag both edges of the price band from the cheap end to the top end. Every slot fills with the part builders add most that is in stock, priced live. The headline total is the core rifle, optics and extras are priced separately, and beside them sits what builders really pay per slot, measured from real part picks. Roll a random build, or open yours in the builder in one click. Computed from over 1 million AR parts selected on GunPartPicker since 2020.
- CompatibilityMuzzle Thread CheckerPick your barrel's caliber and platform, get the standard thread pitch, and see every muzzle device and suppressor in the catalog that actually threads on, with live prices.
- CompatibilitySuppressor Mounts (3D)Put a can on its mount in 3D. Compare SilencerCo ASR, Dead Air KeyMo, SureFire Fast-Attach, HUXWRX QD, Plan B, HUB 1.375x24 and direct thread: what goes on the barrel, what is on the can, how it locks and which cans fit which mounts. Cut it open to see the taper and the baffles, then shop the mounts and cans in stock.
- CompatibilityDI vs Piston (3D)Watch a direct impingement AR-15 and a gas piston HK416 fire in slow motion x-ray 3D. Follow the gas from the port back into the carrier, or into a piston that kicks an op rod, see which bolt runs hot, and compare weight, cleaning, suppressed use, carrier tilt and cost.
- CompatibilityUpper vs Lower Receiver (3D)Take a real AR-15 apart in 3D and see how the upper and lower receiver go together. Push the takedown pin, hinge the upper open on the pivot pin, pull the bolt carrier group and lift the upper off, with every part colored by the half it belongs to.
- CompatibilityHow Muzzle Devices Work (3D)Watch one shot leave an AR-15 muzzle in slow motion 3D through a bare barrel, a flash hider, a compensator, a muzzle brake and a linear comp. See where each sends the gas, and what that does to flash, recoil, muzzle rise and the blast beside you.
- CompatibilityHow a BCG Works (3D)Watch an AR-15 bolt carrier group unlock, extract and lock again in slow motion 3D, then take it apart part by part. See the cam pin turn the bolt out of the barrel extension, and what each part does.
- CompatibilityBuffer Tube and Stock (3D)See an AR-15 buffer tube, end plate, castle nut and stock go on in 3D, walk the stock through its six positions, and put a mil spec and a commercial tube side by side to see why a stock only fits one of them.
- CompatibilityHow a Charging Handle Works (3D)Watch an AR-15 charging handle unlatch and pull the bolt carrier back by its gas key in 3D, then watch the rifle fire while the handle stays put. Compare a standard latch with an ambidextrous one.
- CompatibilityHow the Gas System Works (3D)Watch a shot's gas go up an AR-15's gas port, through the gas block and back down the gas tube to the bolt carrier in slow motion 3D. Turn it down with an adjustable gas block, and see where the port sits on pistol, carbine, mid length and rifle gas.
- CompatibilityFree Float vs Drop In Handguard (3D)Watch an AR-15 free float handguard go on its barrel nut in 3D, lean on a free float and a drop in handguard to see which one moves the barrel, and lock an M-LOK rail section in. Plus M-LOK vs KeyMod and what length fits your barrel.
- CompatibilityHow Triggers Work (3D)Watch a standard trigger, a forced reset trigger and a binary trigger run inside an x-ray AR-15 in slow motion 3D. See the hammer, the disconnector, the FRT's locking bar and the bolt carrier at every step, and what each one needs and where it is legal.
- CompatibilityFRT and Binary Trigger PickerChoose your platform and see every forced reset trigger, binary trigger and Super Safety the catalog carries for it, what the host needs to run one, and where each is in stock.
- CompatibilityGlock Red Dot Fit CheckerPick how your Glock slide is cut and see which red dots mount directly, which need a plate, and the plates and optics in stock right now.
- CompatibilityGlock Size ComparisonPick any two Glocks and see them to scale as real photos sized to Glock's published dimensions, side by side, from behind and as an X-ray, with the difference in length, height, width and weight in one line and the pistols in stock for each.
- CompatibilityP385 Size ComparisonSee the SIG P385 CARRY, COMP and FULL to scale against the P365-XMACRO, the P320 and the Glock 19, 17, 45 and 43X, as real photos sized to the published length and height, with every dimension and where to order one.
- Paint plannerGun Paint PlannerRattle can guns online before you spray. Paint, stencil and camo a real photo of about 1,800 guns: AR-15s, AR-10s, AR-9s, AKs, every Glock, pistols, shotguns and bolt action rifles, the way the rattlecanned guns on r/rattlecannedguns are done, with Krylon, Rust-Oleum, Aluma-Hyde, DuraCoat and Cerakote colors, then get the cans to buy in spray order.
- TuningBuffer Weight CalculatorEnter your gas system, barrel length, buffer tube and ammo, add a suppressor or a fast trigger, and get the buffer weight to start with plus the buffers in stock that match.
- TuningBuffer System (3D)Watch an AR-15 cycle in slow motion, cut open: gas drives the bolt carrier back, the bolt unlocks and throws the brass, the buffer and spring soak it up and send it home. Swap carbine, H, H2 and H3 buffers, add gas or a suppressor, and see the carrier speed, where the brass lands and when it short strokes.
- PlanningNight VisionLook around a real 360 degree scene through Gen 1, Gen 2+, Gen 3 green and white phosphor tubes, digital night vision and thermal. Turn the moon down from full to overcast, switch on an IR light, compare two devices side by side. Or walk a 3D farm at night and spot the people, hogs and deer hiding in it. Then see the PVS-14, PVS-31, GPNVG-18 and the thermal scopes people buy, with prices.
- Planning300 BLK vs 5.56 Race (3D)Race a 9 inch .300 Blackout against a 10.3 inch 5.56, or up to four rifles of your own, down a 3D range. Every rifle fires at once in slow motion, and you get each one's time, speed, energy and drop at 100 to 500 yards.
- CompatibilityCo-Witness Checker (3D)Put a micro red dot, a full size dot or an EOTech on an AR-15 at 1.41, 1.535, 1.57, 1.93 or 2.26 inches and see where your iron sights land in the window, in 3D: absolute, lower 1/3, or under the window.
- PlanningAmmo Cutaway (3D)Cut M193, M855 green tip, M855A1, 77 gr OTM and .300 BLK supersonic and subsonic in half and compare them side by side in 3D: what each bullet is made of, its speed from short barrels, steel targets, and today's price per round. Then watch a .300 BLK round go into a 5.56 chamber.
- TuningWill It Eat Cheap Ammo? (3D)Pick your ammo and your AR-15: barrel and gas length, gas block, buffer, chamber, extractor and how clean it is. See if it will cycle and extract cheap steel case or bulk .223, which part is the weak link on a real 3D rifle, and try each fix to watch the answer change.
- PlanningAstigmatism Optic Test (3D)See a red dot, a circle dot, an EOTech, a prism and an LPVO through eyes with astigmatism, on a 3D AR-15. Pick how strong it is, the light, which way your dot smears and the brightness, and every optic is ranked for those eyes.
- PlanningOptics Without Power (3D)Cut the power to a red dot, an EOTech, a prism, an LPVO or an ACOG on a 3D AR-15 and see what's left in the window, by day and at night, with or without backup iron sights. For a dead battery, a cold morning or an EMP.
- TuningMechanical Offset (3D)See how far under the dot an AR-15 hits at 3 to 25 yards, in 3D: pick your optic height, zero and caliber, and the view through the optic shows the hole under the dot on a 3x5 card, with the hold for every distance.
- TuningEjection Pattern (3D)Tap where your brass lands and a real 3D AR-15 throws it there and tells you if it's overgassed, tuned or short on gas. Or set up your rifle (barrel and gas length, buffer, spring, gas block, suppressor, ammo) and watch where the brass goes, then try each fix and see it move.
- CompatibilityCaliber Conversion (3D)Convert a 5.56 AR-15 to .300 Blackout, 6.5 Grendel, 6mm ARC, .224 Valkyrie, 7.62x39, .350 Legend, .450 Bushmaster, 9mm or .22 LR and see on a real 3D rifle which parts you swap: the barrel, the bolt, the magazines, the buffer, and what stays the same.
- Compatibility5.56 vs .223 Chamber (3D)See a .223 Remington, a 5.56 NATO and a .223 Wylde chamber cut in half in 3D, with a round seated in each. Pick your chamber and your ammo to see where the bullet meets the rifling, why 5.56 in a .223 chamber is unsafe, and why Wylde takes both.
- CompatibilityChrome vs Nitride vs Stainless (3D)See a chrome lined, a nitrided and a stainless 5.56 barrel cut in half at the throat in 3D, then wear them from new to shot out. Compare what each finish is, how long it lasts, how it shoots, and which to buy for your rifle.
- TuningClear AR-15 Jams (3D)See seven AR-15 jams inside a see through receiver in 3D, from a click with no bang to a stovepipe, a double feed, a stuck case and a bolt override, and step through clearing each one. Learn when tap, rack works and when it doesn't.
- TuningTwist Rate and Keyholing (3D)What does 1:7 twist mean, and why does it matter? Fire a bullet down a rifled barrel in 3D and watch it spin, fly and hit the paper. Pick 55, 62 or 77 grain, a 1:7, 1:8, 1:9 or 1:12 barrel, the distance and the air temperature, and see a stable round hole, a wobbling bullet or a keyhole.
- TuningSuppressor Types (3D)How does a suppressor work inside? Cut a can in half in 3D and fire one shot through a cone baffle stack, a one piece monocore and a flow-through can. Watch the gas swirl, zigzag or run straight out the front, see how much comes back at your face, and where the brass lands on a 16 inch carbine or an 11.5 inch SBR.
- TuningGas Block vs Buffer (3D)Can on and brass at 1 o'clock: turn the gas down or add buffer weight? Turn an adjustable gas block's screw in 3D and watch less gas reach the bolt carrier, or step from H to H2 and H3 and watch the same gas push more weight. See where the brass lands, the carrier speed, the gas at your face and when it short strokes.



