5.56 vs .223 Chamber in 3D: the Throat, the Leade and .223 Wylde
See a .223 Remington, a 5.56 NATO and a .223 Wylde chamber cut in half in 3D, with a round seated in each. Pick your chamber and your ammo to see where the bullet meets the rifling, why 5.56 in a .223 chamber is unsafe, and why Wylde takes both.
Quick answer
- 5.56 NATO and .223 Remington rounds have the same outside dimensions. The chambers differ in the throat, just ahead of the case mouth.
- A .223 Remington chamber's rifling reaches full height 0.07" past the case mouth; a 5.56 NATO chamber's takes 0.232", so the bullet gets a longer, gentler run.
- SAAMI calls 5.56 ammo in a .223 Remington chamber an unsafe combination. .223 ammo in a 5.56 chamber is fine, and a .223 Wylde chamber takes both.
Source: SAAMI's .223 Remington chamber and unsafe combinations guidance, the 5.56 NATO and .223 Wylde reamer prints.
See the 5.56 and .223 chambers in 3D
The same round in a .223 Remington, a 5.56 NATO and a .223 Wylde chamber, cut in half. Pick a chamber and your ammo to see where the bullet meets the rifling and whether the pair is safe, or stack all three throats to compare.
5.56 NATO in a .223 Rem chamber
unsafe · throat spread 6x so it shows
Drawn in inches from the chamber prints. The throat differs by a few thousandths, so the close ups spread everything a hair over the rifling 6x across to show it: lengths along the bore stay true, and the leade looks steeper than it is. The whole chamber view is true scale. Rifling is six grooves, 1 turn in 7"; the freebore is lit pale and the leade orange.
5.56 NATO M855 62 gr · .223 REM barrel
Unsafe combination
SAAMI lists 5.56 NATO ammo in a .223 Remington chamber as an unsafe combination. The bullet starts pressed against the short, steep throat, and 5.56 is loaded hotter to begin with, so pressure can climb past what the chamber is built for: blown primers, stuck cases, and worse.
The tight one: a short throat no wider than the bullet and a steep leade, so the bullet sits almost against the rifling.
- Freebore
- 0.224" wide
- Freebore length
- 0.025"
- Leade angle
- 3.18°
- Full rifling
- 0.07" past the mouth
- Takes
- .223 Rem only
| Chamber | Freebore | Leade | Full rifling | .223 Rem ammo | 5.56 NATO ammo |
|---|---|---|---|---|---|
| 0.224" x 0.025" | 3.18° | 0.07" | Safe | Unsafe | |
| 0.2265" x 0.0566" | 1.22° | 0.232" | Safe | Safe | |
| 0.224" x 0.0619" | 1.25° | 0.176" | Safe | Safe |
What's the difference between a 5.56 and a .223 chamber?
The throat. Both chambers hold the same case: same head, same body, same shoulder, same neck. The difference starts at the case mouth, where the bullet sits in a short smooth section called the freebore before the rifling begins, and then the leade, the cone where the lands rise to full height.
A .223 Remington chamber (SAAMI) has a 0.224" freebore only 0.025" long, then a steep 3.2 degree leade: the rifling is at full height 0.07" past the case mouth. A 5.56 NATO chamber has a wider 0.2265" freebore 0.0566" long and a gentle 1.2 degree leade, so full rifling is 0.232" out. A bullet in a 5.56 chamber has room to get moving before it is squeezed into the rifling; in a .223 chamber it starts nearly touching it.
Can you shoot 5.56 in a .223 chamber?
No. SAAMI lists 5.56 NATO ammunition in a .223 Remington chamber as an unsafe combination. Military spec 5.56 is loaded hotter: NATO rates it to 430 MPa (about 62,366 psi) by its own test, while SAAMI's limit for .223 Remington is 55,000 psi. The two are measured differently, so the numbers don't subtract exactly, but the short, tight .223 throat adds to it: the bullet hits the rifling with no running start and pressure climbs faster. The signs are flattened or blown primers, cases that stick, and a bolt that's hard to open; the worst case is a ruptured case.
The other way is fine: .223 Remington ammo is safe in a 5.56 NATO chamber. It may group a little wider in some rifles, because the bullet jumps farther to the rifling, but pressure stays low. A 5.56 stamped barrel or a .223 Wylde barrel takes both.
What is a .223 Wylde chamber?
A hybrid, cut by Bill Wylde for accuracy with both rounds. It keeps the .223's snug 0.224" freebore, so the bullet starts straight, and uses a 5.56 length freebore (0.0619") and a gentle 1.25 degree leade, so 5.56 builds pressure normally. Barrel makers sell it as safe with 5.56 and .223, and it is the common chamber on match and precision AR-15 barrels. Reamers differ by a few thousandths between makers, so read your barrel maker's manual.
How do I know what chamber my AR-15 has?
Read the barrel. The chamber is stamped on the barrel itself, usually under the handguard near the gas block: "5.56 NATO", "5.56", ".223 Wylde" or ".223 Rem". The marking on the lower receiver is not the barrel's: many lowers say "Multi" or "5.56" whatever upper sits on them. If the barrel says only .223 Remington, or nothing, shoot .223 ammo in it or ask the maker. For which upper and barrel parts go together, see upper vs lower receiver, and for ammo by bullet, the M193 vs M855 guide.
.223 Wylde and 5.56 barrels in stock
Barrels that take both 5.56 and .223, ranked by what builders add most, in stock first. One listing per model.
.223 Wylde
Ranked by what builders add most, in stock first. One listing per model.






5.56 NATO
Ranked by what builders add most, in stock first. One listing per model.






Frequently Asked Questions
Can you shoot 5.56 in a .223 chamber?
No. SAAMI lists 5.56 NATO ammo in a .223 Remington chamber as an unsafe combination: 5.56 is loaded hotter, and the .223 chamber's short, tight throat puts the bullet almost against the rifling, so pressure can climb past what the chamber is built for. Signs are flattened or blown primers and sticky extraction.
Can you shoot .223 in a 5.56 chamber?
Yes. .223 Remington ammo is safe in a 5.56 NATO chamber. The bullet jumps a little farther to the rifling, so some rifles group slightly wider with it, but pressure stays low.
What is the difference between a 5.56 and a .223 chamber?
The throat. The case fits the same in both; the 5.56 NATO chamber has a wider freebore (.2265 vs .2240), about twice as long, and a 1.2 degree leade against the .223's 3.2 degrees, so the rifling reaches full height about .23 inch past the case mouth instead of about .07.
Can a .223 Wylde shoot 5.56?
Yes. A .223 Wylde chamber pairs the .223's .2240 freebore with a 5.56 length freebore and a 1.25 degree leade, and barrel makers rate it for both 5.56 NATO and .223 Remington.
Is .223 Wylde more accurate than 5.56?
Often slightly, with match ammo. Its tighter freebore holds the bullet straighter as it starts into the rifling. With bulk FMJ the difference usually disappears in the ammo's own spread.
How do I tell what chamber my AR-15 has?
Read the barrel, not the lower. The chamber is stamped on the barrel, usually under the handguard near the gas block: 5.56 NATO, 5.56, .223 Wylde or .223 Rem. If it says only .223 Rem, or nothing, shoot .223 ammo in it or ask the maker.
Cite this tool: GunPartPicker, “5.56 vs .223 Chamber in 3D: the Throat, the Leade and .223 Wylde”, https://gunpartpicker.net/tools/556-vs-223-chamber. Throat dimensions from the SAAMI .223 Remington chamber and the 5.56 NATO and .223 Wylde reamer prints; barrels confirmed in stock today Free to cite with attribution.
Read next
All guides →More Gun Tools
- TuningTwist Rate CalculatorPick a bullet and a twist rate, get the Miller stability factor, then see barrels with that twist and ammo loaded with that bullet, with today's price per round.
- LegalBarrel and Overall Length CheckerEnter barrel length, muzzle device and how the back end is configured, and see whether the build is a rifle, a short barreled rifle, a pistol or an AOW under federal law, with the barrels in stock at that length.
- CompatibilityUpper vs Lower Receiver (3D)Take a real AR-15 apart in 3D and see how the upper and lower receiver go together. Push the takedown pin, hinge the upper open on the pivot pin, pull the bolt carrier group and lift the upper off, with every part colored by the half it belongs to.
- LegalGun Travel CheckerCan I bring my gun to another state? Pick where you start, where you are going and what is coming along: carry pistol, AR-15, magazines, suppressor, SBR, brace, forced reset or binary trigger, hollow points. Every state on the route is checked for transporting firearms across state lines: magazine limits, assault weapon bans, NFA rules, carry permit type and trigger bans, with what to do before the state line.
- PlanningAR Build Cost CalculatorHow much does it cost to build an AR-15? Pick caliber, barrel length, stock or brace and optic, then drag both edges of the price band from the cheap end to the top end. Every slot fills with the part builders add most that is in stock, priced live. The headline total is the core rifle, optics and extras are priced separately, and beside them sits what builders really pay per slot, measured from real part picks. Roll a random build, or open yours in the builder in one click. Computed from over 1 million AR parts selected on GunPartPicker since 2020.
- CompatibilityMuzzle Thread CheckerPick your barrel's caliber and platform, get the standard thread pitch, and see every muzzle device and suppressor in the catalog that actually threads on, with live prices.
- CompatibilitySuppressor Mounts (3D)Put a can on its mount in 3D. Compare SilencerCo ASR, Dead Air KeyMo, SureFire Fast-Attach, HUXWRX QD, Plan B, HUB 1.375x24 and direct thread: what goes on the barrel, what is on the can, how it locks and which cans fit which mounts. Cut it open to see the taper and the baffles, then shop the mounts and cans in stock.
- CompatibilityDI vs Piston (3D)Watch a direct impingement AR-15 and a gas piston HK416 fire in slow motion x-ray 3D. Follow the gas from the port back into the carrier, or into a piston that kicks an op rod, see which bolt runs hot, and compare weight, cleaning, suppressed use, carrier tilt and cost.
- CompatibilityHow Muzzle Devices Work (3D)Watch one shot leave an AR-15 muzzle in slow motion 3D through a bare barrel, a flash hider, a compensator, a muzzle brake and a linear comp. See where each sends the gas, and what that does to flash, recoil, muzzle rise and the blast beside you.
- CompatibilityHow a BCG Works (3D)Watch an AR-15 bolt carrier group unlock, extract and lock again in slow motion 3D, then take it apart part by part. See the cam pin turn the bolt out of the barrel extension, and what each part does.
- CompatibilityBuffer Tube and Stock (3D)See an AR-15 buffer tube, end plate, castle nut and stock go on in 3D, walk the stock through its six positions, and put a mil spec and a commercial tube side by side to see why a stock only fits one of them.
- CompatibilityHow a Charging Handle Works (3D)Watch an AR-15 charging handle unlatch and pull the bolt carrier back by its gas key in 3D, then watch the rifle fire while the handle stays put. Compare a standard latch with an ambidextrous one.
- CompatibilityHow the Gas System Works (3D)Watch a shot's gas go up an AR-15's gas port, through the gas block and back down the gas tube to the bolt carrier in slow motion 3D. Turn it down with an adjustable gas block, and see where the port sits on pistol, carbine, mid length and rifle gas.
- CompatibilityFree Float vs Drop In Handguard (3D)Watch an AR-15 free float handguard go on its barrel nut in 3D, lean on a free float and a drop in handguard to see which one moves the barrel, and lock an M-LOK rail section in. Plus M-LOK vs KeyMod and what length fits your barrel.
- CompatibilityHow Triggers Work (3D)Watch a standard trigger, a forced reset trigger and a binary trigger run inside an x-ray AR-15 in slow motion 3D. See the hammer, the disconnector, the FRT's locking bar and the bolt carrier at every step, and what each one needs and where it is legal.
- CompatibilityFRT and Binary Trigger PickerChoose your platform and see every forced reset trigger, binary trigger and Super Safety the catalog carries for it, what the host needs to run one, and where each is in stock.
- CompatibilityGlock Red Dot Fit CheckerPick how your Glock slide is cut and see which red dots mount directly, which need a plate, and the plates and optics in stock right now.
- CompatibilityGlock Size ComparisonPick any two Glocks and see them to scale as real photos sized to Glock's published dimensions, side by side, from behind and as an X-ray, with the difference in length, height, width and weight in one line and the pistols in stock for each.
- CompatibilityP385 Size ComparisonSee the SIG P385 CARRY, COMP and FULL to scale against the P365-XMACRO, the P320 and the Glock 19, 17, 45 and 43X, as real photos sized to the published length and height, with every dimension and where to order one.
- Paint plannerGun Paint PlannerRattle can guns online before you spray. Paint, stencil and camo a real photo of about 1,800 guns: AR-15s, AR-10s, AR-9s, AKs, every Glock, pistols, shotguns and bolt action rifles, the way the rattlecanned guns on r/rattlecannedguns are done, with Krylon, Rust-Oleum, Aluma-Hyde, DuraCoat and Cerakote colors, then get the cans to buy in spray order.
- TuningOptic Zero (3D)See where a 25, 36, 50, 100 or 200 yard zero hits on a 3D range, with your ammo, barrel length and optic height. Compare two zeros side by side, look through your red dot, EOTech or LPVO at each distance, then tap where your group hit and get the exact clicks up, down, left and right for your optic.
- TuningBuffer Weight CalculatorEnter your gas system, barrel length, buffer tube and ammo, add a suppressor or a fast trigger, and get the buffer weight to start with plus the buffers in stock that match.
- TuningBuffer System (3D)Watch an AR-15 cycle in slow motion, cut open: gas drives the bolt carrier back, the bolt unlocks and throws the brass, the buffer and spring soak it up and send it home. Swap carbine, H, H2 and H3 buffers, add gas or a suppressor, and see the carrier speed, where the brass lands and when it short strokes.
- LegalSBR Planner (3D)Set the barrel anywhere from 7.5 to 16 inches, put a stock, a brace or a folder on the back, pin a muzzle device or slide on a can. The ruler under the rifle shows whether you've cleared the 16 inch barrel line and the 26 inch overall line. Pick your state for its SBR, suppressor and assault weapon rules, then price every part and open the build in one click.
- PlanningNight VisionLook around a real 360 degree scene through Gen 1, Gen 2+, Gen 3 green and white phosphor tubes, digital night vision and thermal. Turn the moon down from full to overcast, switch on an IR light, compare two devices side by side. Or walk a 3D farm at night and spot the people, hogs and deer hiding in it. Then see the PVS-14, PVS-31, GPNVG-18 and the thermal scopes people buy, with prices.
- Planning300 BLK vs 5.56 Race (3D)Race a 9 inch .300 Blackout against a 10.3 inch 5.56, or up to four rifles of your own, down a 3D range. Every rifle fires at once in slow motion, and you get each one's time, speed, energy and drop at 100 to 500 yards.
- CompatibilityCo-Witness Checker (3D)Put a micro red dot, a full size dot or an EOTech on an AR-15 at 1.41, 1.535, 1.57, 1.93 or 2.26 inches and see where your iron sights land in the window, in 3D: absolute, lower 1/3, or under the window.
- PlanningAmmo Cutaway (3D)Cut M193, M855 green tip, M855A1, 77 gr OTM and .300 BLK supersonic and subsonic in half and compare them side by side in 3D: what each bullet is made of, its speed from short barrels, steel targets, and today's price per round. Then watch a .300 BLK round go into a 5.56 chamber.
- TuningWill It Eat Cheap Ammo? (3D)Pick your ammo and your AR-15: barrel and gas length, gas block, buffer, chamber, extractor and how clean it is. See if it will cycle and extract cheap steel case or bulk .223, which part is the weak link on a real 3D rifle, and try each fix to watch the answer change.
- PlanningAstigmatism Optic Test (3D)See a red dot, a circle dot, an EOTech, a prism and an LPVO through eyes with astigmatism, on a 3D AR-15. Pick how strong it is, the light, which way your dot smears and the brightness, and every optic is ranked for those eyes.
- PlanningOptics Without Power (3D)Cut the power to a red dot, an EOTech, a prism, an LPVO or an ACOG on a 3D AR-15 and see what's left in the window, by day and at night, with or without backup iron sights. For a dead battery, a cold morning or an EMP.
- TuningMechanical Offset (3D)See how far under the dot an AR-15 hits at 3 to 25 yards, in 3D: pick your optic height, zero and caliber, and the view through the optic shows the hole under the dot on a 3x5 card, with the hold for every distance.
- TuningEjection Pattern (3D)Tap where your brass lands and a real 3D AR-15 throws it there and tells you if it's overgassed, tuned or short on gas. Or set up your rifle (barrel and gas length, buffer, spring, gas block, suppressor, ammo) and watch where the brass goes, then try each fix and see it move.
- CompatibilityCaliber Conversion (3D)Convert a 5.56 AR-15 to .300 Blackout, 6.5 Grendel, 6mm ARC, .224 Valkyrie, 7.62x39, .350 Legend, .450 Bushmaster, 9mm or .22 LR and see on a real 3D rifle which parts you swap: the barrel, the bolt, the magazines, the buffer, and what stays the same.
- CompatibilityChrome vs Nitride vs Stainless (3D)See a chrome lined, a nitrided and a stainless 5.56 barrel cut in half at the throat in 3D, then wear them from new to shot out. Compare what each finish is, how long it lasts, how it shoots, and which to buy for your rifle.
- TuningClear AR-15 Jams (3D)See seven AR-15 jams inside a see through receiver in 3D, from a click with no bang to a stovepipe, a double feed, a stuck case and a bolt override, and step through clearing each one. Learn when tap, rack works and when it doesn't.
- TuningTwist Rate and Keyholing (3D)What does 1:7 twist mean, and why does it matter? Fire a bullet down a rifled barrel in 3D and watch it spin, fly and hit the paper. Pick 55, 62 or 77 grain, a 1:7, 1:8, 1:9 or 1:12 barrel, the distance and the air temperature, and see a stable round hole, a wobbling bullet or a keyhole.
- TuningSuppressor Types (3D)How does a suppressor work inside? Cut a can in half in 3D and fire one shot through a cone baffle stack, a one piece monocore and a flow-through can. Watch the gas swirl, zigzag or run straight out the front, see how much comes back at your face, and where the brass lands on a 16 inch carbine or an 11.5 inch SBR.
- TuningGas Block vs Buffer (3D)Can on and brass at 1 o'clock: turn the gas down or add buffer weight? Turn an adjustable gas block's screw in 3D and watch less gas reach the bolt carrier, or step from H to H2 and H3 and watch the same gas push more weight. See where the brass lands, the carrier speed, the gas at your face and when it short strokes.
- AmmoBallistic Gel (3D)Fire M193, M855, 77 gr OTM, .300 Blackout 110 gr TAC-TX or 220 gr subsonic into a block of ballistic gel in 3D, from a 10.3 to 20 inch barrel at 10 to 300 yards. Watch the bullet yaw, break up or open in slow motion, see the stretch cavity and the wound it leaves, how deep it goes against the FBI's 12 to 18 inches, and how far out your barrel keeps 5.56 fast enough to fragment.


