Absolute vs Lower 1/3 Co-Witness in 3D: Red Dot Mount Heights
Put a micro red dot, a full size dot or an EOTech on an AR-15 at 1.41, 1.535, 1.57, 1.93 or 2.26 inches and see where your iron sights land in the window, in 3D: absolute, lower 1/3, or under the window.
Quick answer
- Absolute co-witness puts the optic's center 1.41" over the rail, the height of standard AR-15 iron sights, so the front post sits right under the dot.
- Lower 1/3 raises it to about 1.535" or 1.57", so the irons run through the lower third of the window: on a micro red dot the post sits about 33% of the way up.
- At 1.93" and taller, a micro dot's window sits over the irons entirely (0.145" under it), so you can't see them through it.
Source: GunPartPicker co-witness model: heights from the top of the rail, standard AR-15 irons 1.41" over it, rounded window sizes.
See your co-witness in 3D
Pick an optic, a mount height and your irons. The sight picture shows where the front post sits in the window; the side view shows the two lines, the optic's center and the iron sights, and the gap between them.
Absolute co-witness
Micro dot · 1.41" over the rail · 2.6" over the bore
Drawn to scale in inches. The sight picture is seen from far behind on the optic's center, so heights compare true against the window; with your eye on the stock the post looks a little nearer the middle. Window sizes are rounded. The rear sight folds down for the sight picture.
Micro dot at 1.41" (Absolute)
Absolute co-witness
The front post sits right under the dot, in the middle of the window. Fast to back up with, but the post covers the lower half of the view.
- Optic over the rail
- 1.41"
- Over the bore
- 2.6"
- Irons under center
- 0"
- Up the window
- 50%
| Height | Over the bore | Irons in the window | Co-witness |
|---|---|---|---|
| 2.6" | 50% up | Absolute co-witness | |
| 2.72" | 33% up | Lower 1/3 co-witness | |
| 2.76" | 29% up | Lower 1/3 co-witness | |
| 2.92" | 7% up | Bottom edge only | |
| 3.12" | Under the window | No co-witness: irons under the window | |
| 3.45" | Under the window | No co-witness: irons under the window |
Absolute vs lower 1/3 co-witness: which is better?
Absolute co-witness lines the optic up with the irons: the dot sits right on the front post. If the optic dies you already have a sight picture, with no head movement. The cost is the post filling the bottom half of the window, right under the dot, on every shot.
Lower 1/3 raises the optic about an eighth to a sixth of an inch, so the irons drop into the lower third of the window and the dot floats over clear glass. It's the more popular pick for a fast red dot carbine: a cleaner view, a slightly more upright head, and the irons still there if you drop your cheek a little. An EOTech EXPS is built lower 1/3 (its center is about 1.66" over the rail); an XPS or 512 is absolute.
Neither changes where the bullet goes once you zero, but a taller optic changes how the bullet crosses the line of sight. See it in the optic zero tool.
Red dot mount heights: 1.41 vs 1.535 vs 1.57 vs 1.93 vs 2.26
For a micro red dot (Aimpoint T-2 or Holosun 403 size), with standard AR-15 irons 1.41" over the rail and the rail 1.19" over the bore.
| Height | Sold as | Over the bore | Irons in the window | Co-witness |
|---|---|---|---|---|
| 1.41" | Absolute | 2.6" | 50% up | Absolute co-witness |
| 1.535" | Lower 1/3 | 2.72" | 33% up | Lower 1/3 co-witness |
| 1.57" | Lower 1/3 | 2.76" | 29% up | Lower 1/3 co-witness |
| 1.73" | Lower 1/3 | 2.92" | 7% up | Bottom edge only |
| 1.93" | 1.93" tall | 3.12" | Under the window | No co-witness: irons under the window |
| 2.26" | 2.26" tall | 3.45" | Under the window | No co-witness: irons under the window |
Why run a 1.93 or 2.26 inch mount?
For your head, not your irons. A taller optic lets you shoot with your head up, which suits a helmet, night vision, a gas mask or a plate carrier that pushes the stock up your shoulder. That's why 2.26" mounts are the common pick for duty and night vision rifles.
The cost: no iron sight picture through a micro dot (the irons sit under its window, into the mount), and more height over the bore, so the bullet is farther under the dot up close. At 7 yards a 2.26" mount is about 3.45" over the bore, so you hold nearly that much high on a small close target. Pair a tall mount with taller irons or an offset backup sight if you want a backup.
How to set up a co-witness
- Pick the height first: 1.41" for absolute, 1.535" or 1.57" for lower 1/3 on a micro dot, or a sight with the height built in.
- Mount the optic as far forward on the upper as your eye relief likes; a red dot has no fixed eye relief. Leave room behind it for the rear sight to fold.
- Zero the irons and the optic at the same distance. A red dot is close to parallax free, so with your eye lined up behind the irons the dot sits on the tip of the front post at either height.
- Check it: flip both irons up and look through the optic with your normal cheek weld. The post should sit where the sight picture above shows it. If the dot and the post disagree when you line up the irons, one of the two zeros is off.
Red dot mounts and backup iron sights in stock
Red dot mounts
Ranked by what builders add most, in stock first. One listing per model.






Backup iron sights
Ranked by what builders add most, in stock first. One listing per model.






See where each optic height puts your bullet in the optic zero tool, and plan a whole build to scale with the SBR planner.
Frequently Asked Questions
What is the difference between absolute and lower 1/3 co-witness?
Where your iron sights sit in the optic's window. Absolute co-witness puts the optic's center at the same height as the irons, 1.41 inches over the rail, so the front post sits right under the dot. Lower 1/3 raises the optic about 1/8 to 1/6 of an inch, so the irons sit in the lower third of the window and the dot floats over clear glass.
Is 1.535 or 1.57 lower 1/3?
Both are sold as lower 1/3 for micro red dots. On a window about 3/4 inch tall, 1.535 puts the front post about a third of the way up and 1.57 a little lower. On a larger window the same heights sit a bit higher, between absolute and lower 1/3.
Can you co-witness with a 1.93 inch mount?
Not with a micro red dot and standard irons. At 1.93 inches the iron line runs about 0.15 inch under a micro dot's window, into the mount, so you can't see the irons through the optic. Taller irons or an offset backup sight fix that.
Is an EOTech absolute or lower 1/3?
It depends on the model. The XPS and the 512 sit at absolute co-witness height; the EXPS has a taller base that puts the irons in the lower third of the window.
Which co-witness is best?
Lower 1/3 for most red dot carbines: a clearer window with the irons still there if you need them. Absolute if you want the irons centered and no head movement to use them. A 1.93 or 2.26 inch mount if you shoot with your head up, with a helmet or night vision, and accept no iron sight picture through the optic.
Does mount height change my zero?
It changes the path, not the zero distance. A taller optic sits farther over the bore, so the bullet starts farther under the dot, rises through it at a steeper angle and comes back down farther out. Up close you hold high by about the optic's height over the bore. The optic zero tool shows yours.
Cite this tool: GunPartPicker, “Absolute vs Lower 1/3 Co-Witness in 3D: Red Dot Mount Heights”, https://gunpartpicker.net/tools/absolute-vs-lower-third-co-witness. Heights from the top of the rail to the optic's center, as mount makers list them; window sizes are rounded Free to cite with attribution.
Read next
All guides →More Gun Tools
- TuningOptic Zero (3D)See where a 25, 36, 50, 100 or 200 yard zero hits on a 3D range, with your ammo, barrel length and optic height. Compare two zeros side by side, look through your red dot, EOTech or LPVO at each distance, then tap where your group hit and get the exact clicks up, down, left and right for your optic.
- LegalSBR Planner (3D)Set the barrel anywhere from 7.5 to 16 inches, put a stock, a brace or a folder on the back, pin a muzzle device or slide on a can. The ruler under the rifle shows whether you've cleared the 16 inch barrel line and the 26 inch overall line. Pick your state for its SBR, suppressor and assault weapon rules, then price every part and open the build in one click.
- CompatibilityUpper vs Lower Receiver (3D)Take a real AR-15 apart in 3D and see how the upper and lower receiver go together. Push the takedown pin, hinge the upper open on the pivot pin, pull the bolt carrier group and lift the upper off, with every part colored by the half it belongs to.
- LegalGun Travel CheckerCan I bring my gun to another state? Pick where you start, where you are going and what is coming along: carry pistol, AR-15, magazines, suppressor, SBR, brace, forced reset or binary trigger, hollow points. Every state on the route is checked for transporting firearms across state lines: magazine limits, assault weapon bans, NFA rules, carry permit type and trigger bans, with what to do before the state line.
- PlanningAR Build Cost CalculatorHow much does it cost to build an AR-15? Pick caliber, barrel length, stock or brace and optic, then drag both edges of the price band from the cheap end to the top end. Every slot fills with the part builders add most that is in stock, priced live. The headline total is the core rifle, optics and extras are priced separately, and beside them sits what builders really pay per slot, measured from real part picks. Roll a random build, or open yours in the builder in one click. Computed from over 1 million AR parts selected on GunPartPicker since 2020.
- CompatibilityMuzzle Thread CheckerPick your barrel's caliber and platform, get the standard thread pitch, and see every muzzle device and suppressor in the catalog that actually threads on, with live prices.
- CompatibilitySuppressor Mounts (3D)Put a can on its mount in 3D. Compare SilencerCo ASR, Dead Air KeyMo, SureFire Fast-Attach, HUXWRX QD, Plan B, HUB 1.375x24 and direct thread: what goes on the barrel, what is on the can, how it locks and which cans fit which mounts. Cut it open to see the taper and the baffles, then shop the mounts and cans in stock.
- CompatibilityDI vs Piston (3D)Watch a direct impingement AR-15 and a gas piston HK416 fire in slow motion x-ray 3D. Follow the gas from the port back into the carrier, or into a piston that kicks an op rod, see which bolt runs hot, and compare weight, cleaning, suppressed use, carrier tilt and cost.
- CompatibilityHow Muzzle Devices Work (3D)Watch one shot leave an AR-15 muzzle in slow motion 3D through a bare barrel, a flash hider, a compensator, a muzzle brake and a linear comp. See where each sends the gas, and what that does to flash, recoil, muzzle rise and the blast beside you.
- CompatibilityHow a BCG Works (3D)Watch an AR-15 bolt carrier group unlock, extract and lock again in slow motion 3D, then take it apart part by part. See the cam pin turn the bolt out of the barrel extension, and what each part does.
- CompatibilityBuffer Tube and Stock (3D)See an AR-15 buffer tube, end plate, castle nut and stock go on in 3D, walk the stock through its six positions, and put a mil spec and a commercial tube side by side to see why a stock only fits one of them.
- CompatibilityHow a Charging Handle Works (3D)Watch an AR-15 charging handle unlatch and pull the bolt carrier back by its gas key in 3D, then watch the rifle fire while the handle stays put. Compare a standard latch with an ambidextrous one.
- CompatibilityHow the Gas System Works (3D)Watch a shot's gas go up an AR-15's gas port, through the gas block and back down the gas tube to the bolt carrier in slow motion 3D. Turn it down with an adjustable gas block, and see where the port sits on pistol, carbine, mid length and rifle gas.
- CompatibilityFree Float vs Drop In Handguard (3D)Watch an AR-15 free float handguard go on its barrel nut in 3D, lean on a free float and a drop in handguard to see which one moves the barrel, and lock an M-LOK rail section in. Plus M-LOK vs KeyMod and what length fits your barrel.
- CompatibilityHow Triggers Work (3D)Watch a standard trigger, a forced reset trigger and a binary trigger run inside an x-ray AR-15 in slow motion 3D. See the hammer, the disconnector, the FRT's locking bar and the bolt carrier at every step, and what each one needs and where it is legal.
- CompatibilityFRT and Binary Trigger PickerChoose your platform and see every forced reset trigger, binary trigger and Super Safety the catalog carries for it, what the host needs to run one, and where each is in stock.
- CompatibilityGlock Red Dot Fit CheckerPick how your Glock slide is cut and see which red dots mount directly, which need a plate, and the plates and optics in stock right now.
- CompatibilityGlock Size ComparisonPick any two Glocks and see them to scale as real photos sized to Glock's published dimensions, side by side, from behind and as an X-ray, with the difference in length, height, width and weight in one line and the pistols in stock for each.
- CompatibilityP385 Size ComparisonSee the SIG P385 CARRY, COMP and FULL to scale against the P365-XMACRO, the P320 and the Glock 19, 17, 45 and 43X, as real photos sized to the published length and height, with every dimension and where to order one.
- Paint plannerGun Paint PlannerRattle can guns online before you spray. Paint, stencil and camo a real photo of about 1,800 guns: AR-15s, AR-10s, AR-9s, AKs, every Glock, pistols, shotguns and bolt action rifles, the way the rattlecanned guns on r/rattlecannedguns are done, with Krylon, Rust-Oleum, Aluma-Hyde, DuraCoat and Cerakote colors, then get the cans to buy in spray order.
- TuningTwist Rate CalculatorPick a bullet and a twist rate, get the Miller stability factor, then see barrels with that twist and ammo loaded with that bullet, with today's price per round.
- TuningBuffer Weight CalculatorEnter your gas system, barrel length, buffer tube and ammo, add a suppressor or a fast trigger, and get the buffer weight to start with plus the buffers in stock that match.
- TuningBuffer System (3D)Watch an AR-15 cycle in slow motion, cut open: gas drives the bolt carrier back, the bolt unlocks and throws the brass, the buffer and spring soak it up and send it home. Swap carbine, H, H2 and H3 buffers, add gas or a suppressor, and see the carrier speed, where the brass lands and when it short strokes.
- LegalBarrel and Overall Length CheckerEnter barrel length, muzzle device and how the back end is configured, and see whether the build is a rifle, a short barreled rifle, a pistol or an AOW under federal law, with the barrels in stock at that length.
- PlanningNight VisionLook around a real 360 degree scene through Gen 1, Gen 2+, Gen 3 green and white phosphor tubes, digital night vision and thermal. Turn the moon down from full to overcast, switch on an IR light, compare two devices side by side. Or walk a 3D farm at night and spot the people, hogs and deer hiding in it. Then see the PVS-14, PVS-31, GPNVG-18 and the thermal scopes people buy, with prices.
- Planning300 BLK vs 5.56 Race (3D)Race a 9 inch .300 Blackout against a 10.3 inch 5.56, or up to four rifles of your own, down a 3D range. Every rifle fires at once in slow motion, and you get each one's time, speed, energy and drop at 100 to 500 yards.
- PlanningAmmo Cutaway (3D)Cut M193, M855 green tip, M855A1, 77 gr OTM and .300 BLK supersonic and subsonic in half and compare them side by side in 3D: what each bullet is made of, its speed from short barrels, steel targets, and today's price per round. Then watch a .300 BLK round go into a 5.56 chamber.
- TuningWill It Eat Cheap Ammo? (3D)Pick your ammo and your AR-15: barrel and gas length, gas block, buffer, chamber, extractor and how clean it is. See if it will cycle and extract cheap steel case or bulk .223, which part is the weak link on a real 3D rifle, and try each fix to watch the answer change.
- PlanningAstigmatism Optic Test (3D)See a red dot, a circle dot, an EOTech, a prism and an LPVO through eyes with astigmatism, on a 3D AR-15. Pick how strong it is, the light, which way your dot smears and the brightness, and every optic is ranked for those eyes.
- PlanningOptics Without Power (3D)Cut the power to a red dot, an EOTech, a prism, an LPVO or an ACOG on a 3D AR-15 and see what's left in the window, by day and at night, with or without backup iron sights. For a dead battery, a cold morning or an EMP.
- TuningMechanical Offset (3D)See how far under the dot an AR-15 hits at 3 to 25 yards, in 3D: pick your optic height, zero and caliber, and the view through the optic shows the hole under the dot on a 3x5 card, with the hold for every distance.
- TuningEjection Pattern (3D)Tap where your brass lands and a real 3D AR-15 throws it there and tells you if it's overgassed, tuned or short on gas. Or set up your rifle (barrel and gas length, buffer, spring, gas block, suppressor, ammo) and watch where the brass goes, then try each fix and see it move.
- CompatibilityCaliber Conversion (3D)Convert a 5.56 AR-15 to .300 Blackout, 6.5 Grendel, 6mm ARC, .224 Valkyrie, 7.62x39, .350 Legend, .450 Bushmaster, 9mm or .22 LR and see on a real 3D rifle which parts you swap: the barrel, the bolt, the magazines, the buffer, and what stays the same.
- Compatibility5.56 vs .223 Chamber (3D)See a .223 Remington, a 5.56 NATO and a .223 Wylde chamber cut in half in 3D, with a round seated in each. Pick your chamber and your ammo to see where the bullet meets the rifling, why 5.56 in a .223 chamber is unsafe, and why Wylde takes both.
- CompatibilityChrome vs Nitride vs Stainless (3D)See a chrome lined, a nitrided and a stainless 5.56 barrel cut in half at the throat in 3D, then wear them from new to shot out. Compare what each finish is, how long it lasts, how it shoots, and which to buy for your rifle.
- TuningClear AR-15 Jams (3D)See seven AR-15 jams inside a see through receiver in 3D, from a click with no bang to a stovepipe, a double feed, a stuck case and a bolt override, and step through clearing each one. Learn when tap, rack works and when it doesn't.
- TuningTwist Rate and Keyholing (3D)What does 1:7 twist mean, and why does it matter? Fire a bullet down a rifled barrel in 3D and watch it spin, fly and hit the paper. Pick 55, 62 or 77 grain, a 1:7, 1:8, 1:9 or 1:12 barrel, the distance and the air temperature, and see a stable round hole, a wobbling bullet or a keyhole.
- TuningSuppressor Types (3D)How does a suppressor work inside? Cut a can in half in 3D and fire one shot through a cone baffle stack, a one piece monocore and a flow-through can. Watch the gas swirl, zigzag or run straight out the front, see how much comes back at your face, and where the brass lands on a 16 inch carbine or an 11.5 inch SBR.
- TuningGas Block vs Buffer (3D)Can on and brass at 1 o'clock: turn the gas down or add buffer weight? Turn an adjustable gas block's screw in 3D and watch less gas reach the bolt carrier, or step from H to H2 and H3 and watch the same gas push more weight. See where the brass lands, the carrier speed, the gas at your face and when it short strokes.
- AmmoBallistic Gel (3D)Fire M193, M855, 77 gr OTM, .300 Blackout 110 gr TAC-TX or 220 gr subsonic into a block of ballistic gel in 3D, from a 10.3 to 20 inch barrel at 10 to 300 yards. Watch the bullet yaw, break up or open in slow motion, see the stretch cavity and the wound it leaves, how deep it goes against the FBI's 12 to 18 inches, and how far out your barrel keeps 5.56 fast enough to fragment.


