AR-15 Caliber Conversion in 3D: What Parts Change for Each Caliber
Convert a 5.56 AR-15 to .300 Blackout, 6.5 Grendel, 6mm ARC, .224 Valkyrie, 7.62x39, .350 Legend, .450 Bushmaster, 9mm or .22 LR and see on a real 3D rifle which parts you swap: the barrel, the bolt, the magazines, the buffer, and what stays the same.
Quick answer
- Most AR-15 caliber conversions only change the upper: the barrel, sometimes the bolt, and the magazines. Your lower receiver stays the same.
- .300 Blackout is the easiest: swap the barrel and keep the 5.56 bolt, magazines and buffer. .350 Legend adds its own magazines.
- 6.5 Grendel, 6mm ARC, .224 Valkyrie, 6.8 SPC and 7.62x39 need a barrel, a bolt with a bigger face and their own magazines. 9mm is blowback: a different BCG, buffer and magazines, and no gas system.
Source: cartridge and bolt face specifications, maker conversion guides, and the GunPartPicker catalog.
What parts do I need to change caliber? See it in 3D
Pick the cartridge you want. The parts you swap light up orange on a real 3D AR-15, the ones to check light yellow, and anything that comes off goes red. Tap a part in the list to see it on its own.
5.56 AR-15 to .300 Blackout
Change 1 part
.300 Blackout · Short barrels and suppressors, subsonic loads
Swap the barrel and nothing else. .300 Blackout was made to use the AR-15's own bolt, magazines and buffer, which is why it's the easiest conversion there is.
Watch out: A .300 BLK round fits in a 5.56 chamber and will blow the rifle up if fired. Mark your .300 BLK magazines, and consider dedicated ones: heavy subsonic bullets feed better from them.
Bolt face: 5.56 (.378")
Every part, for .300 Blackout
.300 Blackout barrels in stock
Ranked by what builders add most, in stock first. One listing per model.






.300 Blackout bolt carrier groups in stock
Ranked by what builders add most, in stock first. One listing per model.






.300 Blackout uppers in stock
Or skip the parts: a complete upper drops on your lower.






The parts lists follow each cartridge's common AR-15 setup. Some makers sell their own matched parts; check a barrel and bolt are made to go together.
AR-15 caliber conversion chart
What changes from a 5.56 AR-15 for each cartridge, and whether your 5.56 magazines still work.
| Cartridge | Parts to change | Bolt face | Magazines |
|---|---|---|---|
| .300 Blackout | Barrel | 5.56 (.378") | 5.56 mags work |
| .350 Legend | Barrel, magazine | 5.56 (.378") | Own magazines |
| 6.5 Grendel | Barrel, bolt, magazine | Grendel (.441") | Own magazines |
| 6mm ARC | Barrel, bolt, magazine | Grendel (.441") | Own magazines |
| .224 Valkyrie | Barrel, bolt, magazine | 6.8 SPC (.422") | Own magazines |
| 6.8 SPC | Barrel, bolt, magazine | 6.8 SPC (.422") | Own magazines |
| 7.62x39 | Barrel, bolt, magazine | 7.62x39 (.447") | Own magazines |
| .450 Bushmaster | Barrel, bolt, magazine | .450 Bushmaster (.473") | Own magazines |
| .458 SOCOM | Barrel, bolt | .458 SOCOM (.473") | 5.56 mags work |
| .50 Beowulf | Barrel, bolt, upper receiver | .50 Beowulf (.445" rebated) | 5.56 mags work |
| 9mm | Barrel, bolt, bolt carrier, magazine, gas block and tube, buffer and spring | Blowback, no locking bolt | Own magazines |
| .22 LR | Bolt, bolt carrier, magazine | Rimfire kit, no locking bolt | Own magazines |
Should I buy a complete upper or the parts?
A complete upper is the easy way, and the way most people run two calibers: the barrel, bolt and gas are matched and headspaced at the factory, and swapping calibers is two pins and thirty seconds on the same lower. See how the halves come apart in upper vs lower receiver in 3D.
Swapping parts in your own upper saves money when only the barrel changes, as with .300 Blackout. When the bolt changes too, buy the barrel and bolt together, or have the headspace checked: a bolt and barrel extension that weren't made for each other is the one thing to get right. Price the whole build in the build cost calculator, and check the twist for your bullets in the twist rate calculator.
Can I mix up .300 Blackout and 5.56?
A .300 Blackout round chambers in a 5.56 barrel, and firing it there can destroy the rifle. It's the one real danger of running both on the same magazines. Mark your .300 BLK magazines with paint or colored baseplates, keep the ammo apart, and many shooters use a different color upper or magazine for each. A 5.56 round won't chamber fully in a .300 BLK barrel, but don't try it.
Frequently Asked Questions
What do I need to convert my AR-15 to .300 Blackout?
Only a .300 Blackout barrel. It uses the same bolt, bolt carrier, buffer and magazines as 5.56, so a 5.56 upper becomes a .300 BLK upper with a barrel swap. Mark your .300 BLK magazines: a .300 Blackout round fired in a 5.56 barrel can destroy the rifle.
Can I change the caliber of an AR-15 with just the upper?
Yes, for every AR-15 sized cartridge. The caliber lives in the upper's barrel and bolt, so a complete upper in another caliber drops onto your lower with two pins. You may need magazines for the new cartridge. 9mm is the exception: it also needs a magazine block or a 9mm lower.
Do I need a different bolt for 6.5 Grendel?
Yes. The 6.5 Grendel case is fatter, so it needs a Grendel bolt with a .441 inch face, plus Grendel magazines. The same bolt and magazines work for 6mm ARC.
Which calibers use the standard AR-15 bolt?
5.56, .223, .300 Blackout and .350 Legend all use the standard 5.56 bolt face. 6.5 Grendel and 6mm ARC share a bigger one, .224 Valkyrie uses the 6.8 SPC bolt, and 7.62x39, .450 Bushmaster and .458 SOCOM each need their own.
Do 5.56 magazines work with other calibers?
.300 Blackout runs from 5.56 magazines, and .458 SOCOM and .50 Beowulf feed from them with fewer rounds. 6.5 Grendel, 6mm ARC, .224 Valkyrie, 6.8 SPC, 7.62x39, .350 Legend and 9mm need magazines made for them.
Can an AR-15 shoot .308 or 6.5 Creedmoor?
No. Those are AR-10 sized cartridges, too long for the AR-15's magazine well and bolt. They need an AR-10 (or LR-308) rifle with its own lower.
Can I convert my AR-15 to 9mm?
Yes, but it's the biggest conversion. A 9mm AR is blowback: it needs a 9mm barrel with no gas system, a heavy blowback bolt carrier, a heavy 9mm buffer and Glock or Colt magazines in a magazine block or a dedicated 9mm lower.
Cite this tool: GunPartPicker, “AR-15 Caliber Conversion in 3D: What Parts Change for Each Caliber”, https://gunpartpicker.net/tools/ar-15-caliber-conversion. Data from the GunPartPicker catalog and real community builds, prices checked November 16, 2026. Free to cite with attribution.
Read next
All guides →More Gun Tools
- CompatibilityUpper vs Lower Receiver (3D)Take a real AR-15 apart in 3D and see how the upper and lower receiver go together. Push the takedown pin, hinge the upper open on the pivot pin, pull the bolt carrier group and lift the upper off, with every part colored by the half it belongs to.
- TuningTwist Rate CalculatorPick a bullet and a twist rate, get the Miller stability factor, then see barrels with that twist and ammo loaded with that bullet, with today's price per round.
- PlanningAR Build Cost CalculatorHow much does it cost to build an AR-15? Pick caliber, barrel length, stock or brace and optic, then drag both edges of the price band from the cheap end to the top end. Every slot fills with the part builders add most that is in stock, priced live. The headline total is the core rifle, optics and extras are priced separately, and beside them sits what builders really pay per slot, measured from real part picks. Roll a random build, or open yours in the builder in one click. Computed from over 1 million AR parts selected on GunPartPicker since 2020.
- CompatibilityHow a BCG Works (3D)Watch an AR-15 bolt carrier group unlock, extract and lock again in slow motion 3D, then take it apart part by part. See the cam pin turn the bolt out of the barrel extension, and what each part does.
- LegalGun Travel CheckerCan I bring my gun to another state? Pick where you start, where you are going and what is coming along: carry pistol, AR-15, magazines, suppressor, SBR, brace, forced reset or binary trigger, hollow points. Every state on the route is checked for transporting firearms across state lines: magazine limits, assault weapon bans, NFA rules, carry permit type and trigger bans, with what to do before the state line.
- CompatibilityMuzzle Thread CheckerPick your barrel's caliber and platform, get the standard thread pitch, and see every muzzle device and suppressor in the catalog that actually threads on, with live prices.
- CompatibilitySuppressor Mounts (3D)Put a can on its mount in 3D. Compare SilencerCo ASR, Dead Air KeyMo, SureFire Fast-Attach, HUXWRX QD, Plan B, HUB 1.375x24 and direct thread: what goes on the barrel, what is on the can, how it locks and which cans fit which mounts. Cut it open to see the taper and the baffles, then shop the mounts and cans in stock.
- CompatibilityDI vs Piston (3D)Watch a direct impingement AR-15 and a gas piston HK416 fire in slow motion x-ray 3D. Follow the gas from the port back into the carrier, or into a piston that kicks an op rod, see which bolt runs hot, and compare weight, cleaning, suppressed use, carrier tilt and cost.
- CompatibilityHow Muzzle Devices Work (3D)Watch one shot leave an AR-15 muzzle in slow motion 3D through a bare barrel, a flash hider, a compensator, a muzzle brake and a linear comp. See where each sends the gas, and what that does to flash, recoil, muzzle rise and the blast beside you.
- CompatibilityBuffer Tube and Stock (3D)See an AR-15 buffer tube, end plate, castle nut and stock go on in 3D, walk the stock through its six positions, and put a mil spec and a commercial tube side by side to see why a stock only fits one of them.
- CompatibilityHow a Charging Handle Works (3D)Watch an AR-15 charging handle unlatch and pull the bolt carrier back by its gas key in 3D, then watch the rifle fire while the handle stays put. Compare a standard latch with an ambidextrous one.
- CompatibilityHow the Gas System Works (3D)Watch a shot's gas go up an AR-15's gas port, through the gas block and back down the gas tube to the bolt carrier in slow motion 3D. Turn it down with an adjustable gas block, and see where the port sits on pistol, carbine, mid length and rifle gas.
- CompatibilityFree Float vs Drop In Handguard (3D)Watch an AR-15 free float handguard go on its barrel nut in 3D, lean on a free float and a drop in handguard to see which one moves the barrel, and lock an M-LOK rail section in. Plus M-LOK vs KeyMod and what length fits your barrel.
- CompatibilityHow Triggers Work (3D)Watch a standard trigger, a forced reset trigger and a binary trigger run inside an x-ray AR-15 in slow motion 3D. See the hammer, the disconnector, the FRT's locking bar and the bolt carrier at every step, and what each one needs and where it is legal.
- CompatibilityFRT and Binary Trigger PickerChoose your platform and see every forced reset trigger, binary trigger and Super Safety the catalog carries for it, what the host needs to run one, and where each is in stock.
- CompatibilityGlock Red Dot Fit CheckerPick how your Glock slide is cut and see which red dots mount directly, which need a plate, and the plates and optics in stock right now.
- CompatibilityGlock Size ComparisonPick any two Glocks and see them to scale as real photos sized to Glock's published dimensions, side by side, from behind and as an X-ray, with the difference in length, height, width and weight in one line and the pistols in stock for each.
- CompatibilityP385 Size ComparisonSee the SIG P385 CARRY, COMP and FULL to scale against the P365-XMACRO, the P320 and the Glock 19, 17, 45 and 43X, as real photos sized to the published length and height, with every dimension and where to order one.
- Paint plannerGun Paint PlannerRattle can guns online before you spray. Paint, stencil and camo a real photo of about 1,800 guns: AR-15s, AR-10s, AR-9s, AKs, every Glock, pistols, shotguns and bolt action rifles, the way the rattlecanned guns on r/rattlecannedguns are done, with Krylon, Rust-Oleum, Aluma-Hyde, DuraCoat and Cerakote colors, then get the cans to buy in spray order.
- TuningOptic Zero (3D)See where a 25, 36, 50, 100 or 200 yard zero hits on a 3D range, with your ammo, barrel length and optic height. Compare two zeros side by side, look through your red dot, EOTech or LPVO at each distance, then tap where your group hit and get the exact clicks up, down, left and right for your optic.
- TuningBuffer Weight CalculatorEnter your gas system, barrel length, buffer tube and ammo, add a suppressor or a fast trigger, and get the buffer weight to start with plus the buffers in stock that match.
- TuningBuffer System (3D)Watch an AR-15 cycle in slow motion, cut open: gas drives the bolt carrier back, the bolt unlocks and throws the brass, the buffer and spring soak it up and send it home. Swap carbine, H, H2 and H3 buffers, add gas or a suppressor, and see the carrier speed, where the brass lands and when it short strokes.
- LegalBarrel and Overall Length CheckerEnter barrel length, muzzle device and how the back end is configured, and see whether the build is a rifle, a short barreled rifle, a pistol or an AOW under federal law, with the barrels in stock at that length.
- LegalSBR Planner (3D)Set the barrel anywhere from 7.5 to 16 inches, put a stock, a brace or a folder on the back, pin a muzzle device or slide on a can. The ruler under the rifle shows whether you've cleared the 16 inch barrel line and the 26 inch overall line. Pick your state for its SBR, suppressor and assault weapon rules, then price every part and open the build in one click.
- PlanningNight VisionLook around a real 360 degree scene through Gen 1, Gen 2+, Gen 3 green and white phosphor tubes, digital night vision and thermal. Turn the moon down from full to overcast, switch on an IR light, compare two devices side by side. Or walk a 3D farm at night and spot the people, hogs and deer hiding in it. Then see the PVS-14, PVS-31, GPNVG-18 and the thermal scopes people buy, with prices.
- Planning300 BLK vs 5.56 Race (3D)Race a 9 inch .300 Blackout against a 10.3 inch 5.56, or up to four rifles of your own, down a 3D range. Every rifle fires at once in slow motion, and you get each one's time, speed, energy and drop at 100 to 500 yards.
- CompatibilityCo-Witness Checker (3D)Put a micro red dot, a full size dot or an EOTech on an AR-15 at 1.41, 1.535, 1.57, 1.93 or 2.26 inches and see where your iron sights land in the window, in 3D: absolute, lower 1/3, or under the window.
- PlanningAmmo Cutaway (3D)Cut M193, M855 green tip, M855A1, 77 gr OTM and .300 BLK supersonic and subsonic in half and compare them side by side in 3D: what each bullet is made of, its speed from short barrels, steel targets, and today's price per round. Then watch a .300 BLK round go into a 5.56 chamber.
- TuningWill It Eat Cheap Ammo? (3D)Pick your ammo and your AR-15: barrel and gas length, gas block, buffer, chamber, extractor and how clean it is. See if it will cycle and extract cheap steel case or bulk .223, which part is the weak link on a real 3D rifle, and try each fix to watch the answer change.
- PlanningAstigmatism Optic Test (3D)See a red dot, a circle dot, an EOTech, a prism and an LPVO through eyes with astigmatism, on a 3D AR-15. Pick how strong it is, the light, which way your dot smears and the brightness, and every optic is ranked for those eyes.
- PlanningOptics Without Power (3D)Cut the power to a red dot, an EOTech, a prism, an LPVO or an ACOG on a 3D AR-15 and see what's left in the window, by day and at night, with or without backup iron sights. For a dead battery, a cold morning or an EMP.
- TuningMechanical Offset (3D)See how far under the dot an AR-15 hits at 3 to 25 yards, in 3D: pick your optic height, zero and caliber, and the view through the optic shows the hole under the dot on a 3x5 card, with the hold for every distance.
- TuningEjection Pattern (3D)Tap where your brass lands and a real 3D AR-15 throws it there and tells you if it's overgassed, tuned or short on gas. Or set up your rifle (barrel and gas length, buffer, spring, gas block, suppressor, ammo) and watch where the brass goes, then try each fix and see it move.
- Compatibility5.56 vs .223 Chamber (3D)See a .223 Remington, a 5.56 NATO and a .223 Wylde chamber cut in half in 3D, with a round seated in each. Pick your chamber and your ammo to see where the bullet meets the rifling, why 5.56 in a .223 chamber is unsafe, and why Wylde takes both.
- CompatibilityChrome vs Nitride vs Stainless (3D)See a chrome lined, a nitrided and a stainless 5.56 barrel cut in half at the throat in 3D, then wear them from new to shot out. Compare what each finish is, how long it lasts, how it shoots, and which to buy for your rifle.
- TuningClear AR-15 Jams (3D)See seven AR-15 jams inside a see through receiver in 3D, from a click with no bang to a stovepipe, a double feed, a stuck case and a bolt override, and step through clearing each one. Learn when tap, rack works and when it doesn't.
- TuningTwist Rate and Keyholing (3D)What does 1:7 twist mean, and why does it matter? Fire a bullet down a rifled barrel in 3D and watch it spin, fly and hit the paper. Pick 55, 62 or 77 grain, a 1:7, 1:8, 1:9 or 1:12 barrel, the distance and the air temperature, and see a stable round hole, a wobbling bullet or a keyhole.
- TuningSuppressor Types (3D)How does a suppressor work inside? Cut a can in half in 3D and fire one shot through a cone baffle stack, a one piece monocore and a flow-through can. Watch the gas swirl, zigzag or run straight out the front, see how much comes back at your face, and where the brass lands on a 16 inch carbine or an 11.5 inch SBR.
- TuningGas Block vs Buffer (3D)Can on and brass at 1 o'clock: turn the gas down or add buffer weight? Turn an adjustable gas block's screw in 3D and watch less gas reach the bolt carrier, or step from H to H2 and H3 and watch the same gas push more weight. See where the brass lands, the carrier speed, the gas at your face and when it short strokes.
- AmmoBallistic Gel (3D)Fire M193, M855, 77 gr OTM, .300 Blackout 110 gr TAC-TX or 220 gr subsonic into a block of ballistic gel in 3D, from a 10.3 to 20 inch barrel at 10 to 300 yards. Watch the bullet yaw, break up or open in slow motion, see the stretch cavity and the wound it leaves, how deep it goes against the FBI's 12 to 18 inches, and how far out your barrel keeps 5.56 fast enough to fragment.



