AR-15 Mechanical Offset in 3D: How Low You Hit Up Close
See how far under the dot an AR-15 hits at 3 to 25 yards, in 3D: pick your optic height, zero and caliber, and the view through the optic shows the hole under the dot on a 3x5 card, with the hold for every distance.
Quick answer
- With a lower 1/3 red dot (2.72" over the bore) and a 50 yard zero, 5.56 hits about 2.5 inches under the dot at 3 yards, 2.3 at 7 and 1.2 at 25.
- That's mechanical offset: the optic sits over the bore, so the bullet starts under the line of sight and doesn't reach the dot until the zero distance.
- A 2.26 inch mount raises it to about 2.9 inches at 7 yards. The zero hardly changes it up close: 2.1 inches at 7 yards with a 36 yard zero, 2.4 with a 100.
Source: GunPartPicker trajectory model (G1 drag, sea level, no wind), 5.56 M193 from a 16 inch barrel, optic heights from the top of the rail plus 1.19 inches of rail over the bore.
See your mechanical offset in 3D
Pick your optic's height, your zero, the caliber and how far the target is. The view through the optic puts the dot on a 3x5 card and shows where the bullet lands; Side shows the line of sight over the bore and the gap between them.
2.3" low at 7 yards
2.72" over the bore · 50 yd zero · 5.56
The dot sits on the center of a 3x5 card; the ringed hole is where the bullet lands. The side view is drawn to scale in inches. Paths are from the same G1 model as the optic zero tool.
1.535" lower 1/3 · 50 yard zero · 5.56
Hold 2.3" high at 7 yards
With the optic 2.72" over the bore, the bullet starts that far under the dot and climbs toward it at 6.1 MOA. At 7 yards it hits 2.3" low, so put the dot that much over the spot you need to hit. It reaches the dot at 50 yards.
- Over the bore
- 2.72"
- Bore angle
- 6.1 MOA
- At 7 yd
- 2.3" low
- In MOA
- 31.1 MOA
| Optic | 3 yd | 5 yd | 7 yd | 10 yd | 15 yd | 25 yd |
|---|---|---|---|---|---|---|
What is mechanical offset?
The distance between your optic and your bore. Your eye looks along the optic, a couple of inches over the barrel, so the bullet starts that far under where you're looking. The barrel is tilted up a few MOA to bring the bullet up to the dot at your zero, but up close it hasn't climbed much yet, so it hits low by almost the full height.
It matters on small targets close in: a head box, a lock, a hostage target, or a steel plate's edge. At 7 yards a lower 1/3 dot hits about 2.3 inches low. Aim at the bottom of a 3x5 card and you miss under it.
It isn't a zero problem. Every common zero (36, 50 or 100 yards) puts the bullet within a few tenths of an inch of the same spot inside 10 yards, because the bore angle is tiny next to the offset. Only the optic's height moves it much. See the whole arc past the zero in the optic zero tool.
AR-15 close range holds by optic height and zero
Inches under the dot with 5.56 M193 from a 16 inch barrel. Hold that much high to hit where you want.
| Optic and zero | Over bore | 3 yd | 5 yd | 7 yd | 10 yd | 15 yd | 25 yd |
|---|---|---|---|---|---|---|---|
| 1.41" absolute, 36 yd zero | 2.6" | 2.4" | 2.2" | 2.1" | 1.8" | 1.5" | 0.7" |
| 1.535" lower 1/3, 36 yd zero | 2.72" | 2.5" | 2.3" | 2.1" | 1.9" | 1.5" | 0.8" |
| 1.93" (LPVO or tall dot), 36 yd zero | 3.12" | 2.8" | 2.7" | 2.5" | 2.2" | 1.8" | 0.9" |
| 2.26" tall dot, 36 yd zero | 3.45" | 3.1" | 2.9" | 2.7" | 2.4" | 1.9" | 1.0" |
| 1.41" absolute, 50 yd zero | 2.6" | 2.4" | 2.3" | 2.2" | 2.0" | 1.7" | 1.2" |
| 1.535" lower 1/3, 50 yd zero | 2.72" | 2.5" | 2.4" | 2.3" | 2.1" | 1.8" | 1.2" |
| 1.93" (LPVO or tall dot), 50 yd zero | 3.12" | 2.9" | 2.8" | 2.6" | 2.4" | 2.1" | 1.4" |
| 2.26" tall dot, 50 yd zero | 3.45" | 3.2" | 3.1" | 2.9" | 2.7" | 2.3" | 1.6" |
| 1.41" absolute, 100 yd zero | 2.6" | 2.5" | 2.4" | 2.3" | 2.1" | 1.9" | 1.6" |
| 1.535" lower 1/3, 100 yd zero | 2.72" | 2.6" | 2.5" | 2.4" | 2.3" | 2.0" | 1.6" |
| 1.93" (LPVO or tall dot), 100 yd zero | 3.12" | 3.0" | 2.9" | 2.8" | 2.6" | 2.4" | 1.9" |
| 2.26" tall dot, 100 yd zero | 3.45" | 3.3" | 3.2" | 3.1" | 2.9" | 2.7" | 2.2" |
How to train for mechanical offset
- Find your number: pick your optic height above and note the hold at 3, 7 and 15 yards. For most red dot carbines it's a little over 2 inches.
- Put a 3x5 card at 7 yards and hold the dot at the card's top edge. The hits should land in the card's middle.
- Shoot small: a 1 inch dot or a square on the card makes the offset obvious, where a big target hides it.
- Taller mounts cost more offset. If you run a 2.26 inch mount for a helmet or night vision, practice its bigger hold too.
Red dot mounts in stock
Ranked by what builders add most, in stock first. One listing per model.






A lower mount means less offset. If your dot smears, compare optics in the red dot astigmatism tool.
Frequently Asked Questions
What is mechanical offset on an AR-15?
The height of the optic over the bore, about 2.6 to 3.5 inches on an AR-15. The bullet starts that far under the line of sight, so up close it hits low by almost that much, and it doesn't reach the dot until the zero distance.
How low does an AR-15 hit at 7 yards?
About 2.3 inches with a lower 1/3 red dot and a 50 yard zero, and about 2.9 with a 2.26 inch mount. Hold that much high on a small target.
Does my zero change mechanical offset?
Hardly up close. Inside 10 yards a 36, 50 or 100 yard zero puts the bullet within a few tenths of an inch of the same spot, because the barrel's tilt is tiny next to the optic's height. The optic's height is what moves it.
Is mechanical offset worse with a tall mount?
Yes. Every extra inch of mount height is about an extra inch of offset up close: a 2.26 inch mount hits about 0.6 inch lower than a 1.535 inch one at 7 yards.
How do I practice mechanical offset?
Put a 3x5 card at 7 yards, hold the dot at the card's top edge and shoot. With a red dot carbine the hits land near the middle of the card. Small aiming points make the offset obvious.
Does 9mm or .300 Blackout change the offset?
A little. A slower round's barrel tilts up more for the same zero, so it climbs faster: 9mm from a carbine hits a few tenths of an inch higher up close than 5.56. The tool shows each caliber.
Cite this tool: GunPartPicker, “AR-15 Mechanical Offset in 3D: How Low You Hit Up Close”, https://gunpartpicker.net/tools/ar-15-mechanical-offset. Trajectories from a G1 drag model with rounded muzzle velocities; check yours on paper Free to cite with attribution.
Read next
All guides →More Gun Tools
- TuningOptic Zero (3D)See where a 25, 36, 50, 100 or 200 yard zero hits on a 3D range, with your ammo, barrel length and optic height. Compare two zeros side by side, look through your red dot, EOTech or LPVO at each distance, then tap where your group hit and get the exact clicks up, down, left and right for your optic.
- PlanningAstigmatism Optic Test (3D)See a red dot, a circle dot, an EOTech, a prism and an LPVO through eyes with astigmatism, on a 3D AR-15. Pick how strong it is, the light, which way your dot smears and the brightness, and every optic is ranked for those eyes.
- LegalSBR Planner (3D)Set the barrel anywhere from 7.5 to 16 inches, put a stock, a brace or a folder on the back, pin a muzzle device or slide on a can. The ruler under the rifle shows whether you've cleared the 16 inch barrel line and the 26 inch overall line. Pick your state for its SBR, suppressor and assault weapon rules, then price every part and open the build in one click.
- LegalGun Travel CheckerCan I bring my gun to another state? Pick where you start, where you are going and what is coming along: carry pistol, AR-15, magazines, suppressor, SBR, brace, forced reset or binary trigger, hollow points. Every state on the route is checked for transporting firearms across state lines: magazine limits, assault weapon bans, NFA rules, carry permit type and trigger bans, with what to do before the state line.
- PlanningAR Build Cost CalculatorHow much does it cost to build an AR-15? Pick caliber, barrel length, stock or brace and optic, then drag both edges of the price band from the cheap end to the top end. Every slot fills with the part builders add most that is in stock, priced live. The headline total is the core rifle, optics and extras are priced separately, and beside them sits what builders really pay per slot, measured from real part picks. Roll a random build, or open yours in the builder in one click. Computed from over 1 million AR parts selected on GunPartPicker since 2020.
- CompatibilityMuzzle Thread CheckerPick your barrel's caliber and platform, get the standard thread pitch, and see every muzzle device and suppressor in the catalog that actually threads on, with live prices.
- CompatibilitySuppressor Mounts (3D)Put a can on its mount in 3D. Compare SilencerCo ASR, Dead Air KeyMo, SureFire Fast-Attach, HUXWRX QD, Plan B, HUB 1.375x24 and direct thread: what goes on the barrel, what is on the can, how it locks and which cans fit which mounts. Cut it open to see the taper and the baffles, then shop the mounts and cans in stock.
- CompatibilityDI vs Piston (3D)Watch a direct impingement AR-15 and a gas piston HK416 fire in slow motion x-ray 3D. Follow the gas from the port back into the carrier, or into a piston that kicks an op rod, see which bolt runs hot, and compare weight, cleaning, suppressed use, carrier tilt and cost.
- CompatibilityUpper vs Lower Receiver (3D)Take a real AR-15 apart in 3D and see how the upper and lower receiver go together. Push the takedown pin, hinge the upper open on the pivot pin, pull the bolt carrier group and lift the upper off, with every part colored by the half it belongs to.
- CompatibilityHow Muzzle Devices Work (3D)Watch one shot leave an AR-15 muzzle in slow motion 3D through a bare barrel, a flash hider, a compensator, a muzzle brake and a linear comp. See where each sends the gas, and what that does to flash, recoil, muzzle rise and the blast beside you.
- CompatibilityHow a BCG Works (3D)Watch an AR-15 bolt carrier group unlock, extract and lock again in slow motion 3D, then take it apart part by part. See the cam pin turn the bolt out of the barrel extension, and what each part does.
- CompatibilityBuffer Tube and Stock (3D)See an AR-15 buffer tube, end plate, castle nut and stock go on in 3D, walk the stock through its six positions, and put a mil spec and a commercial tube side by side to see why a stock only fits one of them.
- CompatibilityHow a Charging Handle Works (3D)Watch an AR-15 charging handle unlatch and pull the bolt carrier back by its gas key in 3D, then watch the rifle fire while the handle stays put. Compare a standard latch with an ambidextrous one.
- CompatibilityHow the Gas System Works (3D)Watch a shot's gas go up an AR-15's gas port, through the gas block and back down the gas tube to the bolt carrier in slow motion 3D. Turn it down with an adjustable gas block, and see where the port sits on pistol, carbine, mid length and rifle gas.
- CompatibilityFree Float vs Drop In Handguard (3D)Watch an AR-15 free float handguard go on its barrel nut in 3D, lean on a free float and a drop in handguard to see which one moves the barrel, and lock an M-LOK rail section in. Plus M-LOK vs KeyMod and what length fits your barrel.
- CompatibilityHow Triggers Work (3D)Watch a standard trigger, a forced reset trigger and a binary trigger run inside an x-ray AR-15 in slow motion 3D. See the hammer, the disconnector, the FRT's locking bar and the bolt carrier at every step, and what each one needs and where it is legal.
- CompatibilityFRT and Binary Trigger PickerChoose your platform and see every forced reset trigger, binary trigger and Super Safety the catalog carries for it, what the host needs to run one, and where each is in stock.
- CompatibilityGlock Red Dot Fit CheckerPick how your Glock slide is cut and see which red dots mount directly, which need a plate, and the plates and optics in stock right now.
- CompatibilityGlock Size ComparisonPick any two Glocks and see them to scale as real photos sized to Glock's published dimensions, side by side, from behind and as an X-ray, with the difference in length, height, width and weight in one line and the pistols in stock for each.
- CompatibilityP385 Size ComparisonSee the SIG P385 CARRY, COMP and FULL to scale against the P365-XMACRO, the P320 and the Glock 19, 17, 45 and 43X, as real photos sized to the published length and height, with every dimension and where to order one.
- Paint plannerGun Paint PlannerRattle can guns online before you spray. Paint, stencil and camo a real photo of about 1,800 guns: AR-15s, AR-10s, AR-9s, AKs, every Glock, pistols, shotguns and bolt action rifles, the way the rattlecanned guns on r/rattlecannedguns are done, with Krylon, Rust-Oleum, Aluma-Hyde, DuraCoat and Cerakote colors, then get the cans to buy in spray order.
- TuningTwist Rate CalculatorPick a bullet and a twist rate, get the Miller stability factor, then see barrels with that twist and ammo loaded with that bullet, with today's price per round.
- TuningBuffer Weight CalculatorEnter your gas system, barrel length, buffer tube and ammo, add a suppressor or a fast trigger, and get the buffer weight to start with plus the buffers in stock that match.
- TuningBuffer System (3D)Watch an AR-15 cycle in slow motion, cut open: gas drives the bolt carrier back, the bolt unlocks and throws the brass, the buffer and spring soak it up and send it home. Swap carbine, H, H2 and H3 buffers, add gas or a suppressor, and see the carrier speed, where the brass lands and when it short strokes.
- LegalBarrel and Overall Length CheckerEnter barrel length, muzzle device and how the back end is configured, and see whether the build is a rifle, a short barreled rifle, a pistol or an AOW under federal law, with the barrels in stock at that length.
- PlanningNight VisionLook around a real 360 degree scene through Gen 1, Gen 2+, Gen 3 green and white phosphor tubes, digital night vision and thermal. Turn the moon down from full to overcast, switch on an IR light, compare two devices side by side. Or walk a 3D farm at night and spot the people, hogs and deer hiding in it. Then see the PVS-14, PVS-31, GPNVG-18 and the thermal scopes people buy, with prices.
- Planning300 BLK vs 5.56 Race (3D)Race a 9 inch .300 Blackout against a 10.3 inch 5.56, or up to four rifles of your own, down a 3D range. Every rifle fires at once in slow motion, and you get each one's time, speed, energy and drop at 100 to 500 yards.
- CompatibilityCo-Witness Checker (3D)Put a micro red dot, a full size dot or an EOTech on an AR-15 at 1.41, 1.535, 1.57, 1.93 or 2.26 inches and see where your iron sights land in the window, in 3D: absolute, lower 1/3, or under the window.
- PlanningAmmo Cutaway (3D)Cut M193, M855 green tip, M855A1, 77 gr OTM and .300 BLK supersonic and subsonic in half and compare them side by side in 3D: what each bullet is made of, its speed from short barrels, steel targets, and today's price per round. Then watch a .300 BLK round go into a 5.56 chamber.
- TuningWill It Eat Cheap Ammo? (3D)Pick your ammo and your AR-15: barrel and gas length, gas block, buffer, chamber, extractor and how clean it is. See if it will cycle and extract cheap steel case or bulk .223, which part is the weak link on a real 3D rifle, and try each fix to watch the answer change.
- PlanningOptics Without Power (3D)Cut the power to a red dot, an EOTech, a prism, an LPVO or an ACOG on a 3D AR-15 and see what's left in the window, by day and at night, with or without backup iron sights. For a dead battery, a cold morning or an EMP.
- TuningEjection Pattern (3D)Tap where your brass lands and a real 3D AR-15 throws it there and tells you if it's overgassed, tuned or short on gas. Or set up your rifle (barrel and gas length, buffer, spring, gas block, suppressor, ammo) and watch where the brass goes, then try each fix and see it move.
- CompatibilityCaliber Conversion (3D)Convert a 5.56 AR-15 to .300 Blackout, 6.5 Grendel, 6mm ARC, .224 Valkyrie, 7.62x39, .350 Legend, .450 Bushmaster, 9mm or .22 LR and see on a real 3D rifle which parts you swap: the barrel, the bolt, the magazines, the buffer, and what stays the same.
- Compatibility5.56 vs .223 Chamber (3D)See a .223 Remington, a 5.56 NATO and a .223 Wylde chamber cut in half in 3D, with a round seated in each. Pick your chamber and your ammo to see where the bullet meets the rifling, why 5.56 in a .223 chamber is unsafe, and why Wylde takes both.
- CompatibilityChrome vs Nitride vs Stainless (3D)See a chrome lined, a nitrided and a stainless 5.56 barrel cut in half at the throat in 3D, then wear them from new to shot out. Compare what each finish is, how long it lasts, how it shoots, and which to buy for your rifle.
- TuningClear AR-15 Jams (3D)See seven AR-15 jams inside a see through receiver in 3D, from a click with no bang to a stovepipe, a double feed, a stuck case and a bolt override, and step through clearing each one. Learn when tap, rack works and when it doesn't.
- TuningTwist Rate and Keyholing (3D)What does 1:7 twist mean, and why does it matter? Fire a bullet down a rifled barrel in 3D and watch it spin, fly and hit the paper. Pick 55, 62 or 77 grain, a 1:7, 1:8, 1:9 or 1:12 barrel, the distance and the air temperature, and see a stable round hole, a wobbling bullet or a keyhole.
- TuningSuppressor Types (3D)How does a suppressor work inside? Cut a can in half in 3D and fire one shot through a cone baffle stack, a one piece monocore and a flow-through can. Watch the gas swirl, zigzag or run straight out the front, see how much comes back at your face, and where the brass lands on a 16 inch carbine or an 11.5 inch SBR.
- TuningGas Block vs Buffer (3D)Can on and brass at 1 o'clock: turn the gas down or add buffer weight? Turn an adjustable gas block's screw in 3D and watch less gas reach the bolt carrier, or step from H to H2 and H3 and watch the same gas push more weight. See where the brass lands, the carrier speed, the gas at your face and when it short strokes.
- AmmoBallistic Gel (3D)Fire M193, M855, 77 gr OTM, .300 Blackout 110 gr TAC-TX or 220 gr subsonic into a block of ballistic gel in 3D, from a 10.3 to 20 inch barrel at 10 to 300 yards. Watch the bullet yaw, break up or open in slow motion, see the stretch cavity and the wound it leaves, how deep it goes against the FBI's 12 to 18 inches, and how far out your barrel keeps 5.56 fast enough to fragment.

