AR-15 Ejection Pattern Chart in 3D: Where Should Brass Land?
Tap where your brass lands and a real 3D AR-15 throws it there and tells you if it's overgassed, tuned or short on gas. Or set up your rifle (barrel and gas length, buffer, spring, gas block, suppressor, ammo) and watch where the brass goes, then try each fix and see it move.
Quick answer
- A tuned AR-15 throws its brass at about 3 to 4:30 on a clock where 12 is down the barrel and 3 is straight out to the right.
- Brass at 1 or 2 o'clock means it's overgassed: common on short carbine gas barrels and suppressed rifles. A heavier buffer or an adjustable gas block fixes it.
- Brass at 5 o'clock or behind you means it's short on gas. Check the bolt locks back on the last round, then clean and lube the carrier, check the gas key and gas block, or go a buffer lighter.
Source: how common AR-15 gas, buffer and suppressor setups are known to run, and the GunPartPicker catalog.
Where should AR-15 brass land? Check yours in 3D
Tap where your brass lands and a real 3D AR-15 throws it there and tells you what it means. Or set up your rifle (barrel, buffer, gas block, suppressor, ammo) and watch where its brass goes. Each fix lights its part on the rifle; tap Try it to see the brass move.
Your brass · 2:00 o'clock
A little overgassed
12 o'clock is down the barrel and 3 o'clock is straight out to your right. The ground is shrunk to fit; the hour is what counts.
Tap where your brass lands
Shoot a full magazine standing still and look down: the clock is yours, with the muzzle at 12.
2:00 o'clock · 2 to 3 o'clock
A little overgassed
More gas than it needs. Most rifles run fine like this and it's normal for short carbine gas barrels and suppressed rifles. A heavier buffer softens it and saves parts.
- Gas at the carrier
- 128% of tuned
- Brass lands about
- 10.5 ft away
How to fix an overgassed AR-15
- 1
Go one buffer heavier: H (3.8 oz)
The cheapest fix. A heavier buffer slows the carrier, so it unlocks a hair later and comes back softer. Step one weight at a time and check it still locks back on the last round.
- 2
Fit an adjustable gas block
Turns the gas down at the source, the way to tune a rifle exactly, and the answer for a suppressor. Close it until the bolt stops locking back on empty, then open it two clicks.
- 3
Run an extra power buffer spring
A stiffer spring (Sprinco blue, a flat wire) slows the carrier on the way back and closes the bolt harder. A small step, and good with a heavier buffer.
- 4
Check the barrel's gas port size
Some budget barrels are drilled big to run every load. If a heavy buffer and a tuned block still throw brass forward, the port is the reason, and an adjustable block is the fix.
A rule of thumb from how common AR-15 setups run, not a measurement. Gas ports, buffers, ejector springs, brass deflectors and ammo lots all vary: the range is the final word.
Carbine, H, H2 and H3 buffers in stock
The cheapest way to tune the gas: one buffer weight at a time.






Adjustable gas blocks in stock
Ranked by what builders add most, in stock first. One listing per model.






Buffer springs in stock
Ranked by what builders add most, in stock first. One listing per model.






AR-15 ejection pattern chart
What each part of the clock says about the gas, with 12 o'clock down the barrel.
| Brass lands | What it means | What it does |
|---|---|---|
| 12 to 2 o'clock | Overgassed | Too much gas is reaching the carrier. It slams back early and hard, throws brass forward and far, and wears the extractor, cam pin and buffer. Expect torn rims, dented case mouths and a harsh, bouncy recoil. |
| 2 to 3 o'clock | A little overgassed | More gas than it needs. Most rifles run fine like this and it's normal for short carbine gas barrels and suppressed rifles. A heavier buffer softens it and saves parts. |
| 3 to 4:30 | Tuned | Right where an AR-15 should be. The carrier gets enough gas to cycle, lock back on empty and strip the next round, without beating itself up. |
| 4:30 to 5 | A little short on gas | Running on the soft side. It may be fine with this ammo and short stroke on milder loads, in the cold or when it gets dirty. Check the bolt locks back on the last round. |
| 5 o'clock and behind | Short on gas | Not enough gas to cycle reliably. Expect weak ejection, brass dribbling out behind you, the bolt not locking back on empty and failures to feed the next round. |
Where common AR-15 setups throw brass
Clean rifles shooting full power 5.56 with a standard spring, as this tool scores them.
| Rifle | Brass at | Gas |
|---|---|---|
| 16" carbine gas, carbine buffer | 2:30 | A little overgassed |
| 16" carbine gas, H2 buffer | 3:30 | Tuned |
| 16" mid length, carbine buffer | 3:15 | Tuned |
| 14.5" carbine gas (M4), H buffer | 3:00 | Tuned |
| 10.5" carbine gas, H buffer | 2:45 | A little overgassed |
| 10.5" carbine gas, H buffer, suppressed | 1:15 | Overgassed |
| 10.5" suppressed, H3 and adjustable block | 4:00 | Tuned |
| 18" rifle length, H buffer | 4:15 | Tuned |
| 20" rifle, rifle buffer | 3:45 | Tuned |
Why does the ejection pattern show the gas?
The ejector in the bolt face pushes on one side of the case rim as the bolt carrier travels back, so the case pivots out of the port. How far it swings before it clears the port depends on how fast the carrier is moving. A carrier with too much gas comes back fast: the case barely pivots before it's flung out, so it flies forward, toward 1 or 2 o'clock. A slow carrier gives the case time to swing further, and it dribbles out toward 5 o'clock or behind you. See the parts move in how an AR-15 BCG works and how the gas system works.
The brass deflector bump on the upper, the ejector spring and how you hold the rifle all nudge it too, so read the pattern from a full magazine, not one round, and always together with the other sign: the bolt should lock back on the last round every time.
How do I tune an overgassed AR-15?
Start with the buffer, one weight at a time: carbine to H, H to H2, H2 to H3. It's the cheapest fix and it keeps the rifle running every load. The buffer weight calculator gives a starting point, and the buffer system in 3D shows what the buffer does. An extra power spring adds a little more.
If a suppressor is in the plan, an adjustable gas block is the real answer: close it until the bolt stops locking back on an empty magazine, then open it two clicks. Check that tune with your cheapest ammo too, because mild .223 and steel case need more gas than 5.56.
Frequently Asked Questions
Where should brass eject on an AR-15?
At about 3 to 4:30 on a clock where 12 is straight down the barrel and 3 is straight out to your right. That says the carrier gets enough gas to cycle and lock back on empty without beating itself up. Read it from a full magazine standing still, not from one round.
What does brass ejecting at 1 or 2 o'clock mean?
The rifle is overgassed. The carrier comes back so fast the case is flung forward before it can swing out. It's common on short carbine gas barrels and suppressed rifles. Go one buffer heavier, add an extra power spring, or fit an adjustable gas block.
What does brass ejecting at 5 or 6 o'clock mean?
The rifle is short on gas. The carrier is moving slowly, so the case swings out late and dribbles behind you. Check the bolt locks back on the last round, then clean and lube the carrier, make sure the gas key is staked and the gas block sits over the port, and try one buffer lighter or full power 5.56.
Does a suppressor change the ejection pattern?
Yes. A suppressor's back pressure works like more gas, so brass moves forward, often from 3 or 4 o'clock to 1 or 2. A heavier buffer, a low back pressure can or an adjustable gas block brings it back.
Does buffer weight change where brass lands?
Yes. A heavier buffer slows the carrier, so the brass lands later on the clock and closer. Going from a carbine buffer to an H2 on a 16 inch carbine gas rifle usually moves brass from about 2 o'clock to about 3:30.
Is a 2 o'clock ejection pattern bad?
Not dangerous, and plenty of rifles run that way for years. It does wear the extractor, cam pin and buffer faster and makes the recoil harsher, so it's worth one buffer step heavier if the rifle still locks back on empty with your mildest ammo.
Is this tool exact?
No. It's a rule of thumb built from how common AR-15 setups are known to run. Gas ports, ejector springs, brass deflectors and ammo lots all vary, and how you hold the rifle moves the brass too. The range is the final word.
Cite this tool: GunPartPicker, “AR-15 Ejection Pattern Chart in 3D: Where Should Brass Land?”, https://gunpartpicker.net/tools/ar-15-ejection-pattern. Data from the GunPartPicker catalog and real community builds, prices checked November 16, 2026. Free to cite with attribution.
Read next
All guides →More Gun Tools
- TuningBuffer Weight CalculatorEnter your gas system, barrel length, buffer tube and ammo, add a suppressor or a fast trigger, and get the buffer weight to start with plus the buffers in stock that match.
- CompatibilityHow the Gas System Works (3D)Watch a shot's gas go up an AR-15's gas port, through the gas block and back down the gas tube to the bolt carrier in slow motion 3D. Turn it down with an adjustable gas block, and see where the port sits on pistol, carbine, mid length and rifle gas.
- TuningBuffer System (3D)Watch an AR-15 cycle in slow motion, cut open: gas drives the bolt carrier back, the bolt unlocks and throws the brass, the buffer and spring soak it up and send it home. Swap carbine, H, H2 and H3 buffers, add gas or a suppressor, and see the carrier speed, where the brass lands and when it short strokes.
- CompatibilityHow a BCG Works (3D)Watch an AR-15 bolt carrier group unlock, extract and lock again in slow motion 3D, then take it apart part by part. See the cam pin turn the bolt out of the barrel extension, and what each part does.
- LegalGun Travel CheckerCan I bring my gun to another state? Pick where you start, where you are going and what is coming along: carry pistol, AR-15, magazines, suppressor, SBR, brace, forced reset or binary trigger, hollow points. Every state on the route is checked for transporting firearms across state lines: magazine limits, assault weapon bans, NFA rules, carry permit type and trigger bans, with what to do before the state line.
- PlanningAR Build Cost CalculatorHow much does it cost to build an AR-15? Pick caliber, barrel length, stock or brace and optic, then drag both edges of the price band from the cheap end to the top end. Every slot fills with the part builders add most that is in stock, priced live. The headline total is the core rifle, optics and extras are priced separately, and beside them sits what builders really pay per slot, measured from real part picks. Roll a random build, or open yours in the builder in one click. Computed from over 1 million AR parts selected on GunPartPicker since 2020.
- CompatibilityMuzzle Thread CheckerPick your barrel's caliber and platform, get the standard thread pitch, and see every muzzle device and suppressor in the catalog that actually threads on, with live prices.
- CompatibilitySuppressor Mounts (3D)Put a can on its mount in 3D. Compare SilencerCo ASR, Dead Air KeyMo, SureFire Fast-Attach, HUXWRX QD, Plan B, HUB 1.375x24 and direct thread: what goes on the barrel, what is on the can, how it locks and which cans fit which mounts. Cut it open to see the taper and the baffles, then shop the mounts and cans in stock.
- CompatibilityDI vs Piston (3D)Watch a direct impingement AR-15 and a gas piston HK416 fire in slow motion x-ray 3D. Follow the gas from the port back into the carrier, or into a piston that kicks an op rod, see which bolt runs hot, and compare weight, cleaning, suppressed use, carrier tilt and cost.
- CompatibilityUpper vs Lower Receiver (3D)Take a real AR-15 apart in 3D and see how the upper and lower receiver go together. Push the takedown pin, hinge the upper open on the pivot pin, pull the bolt carrier group and lift the upper off, with every part colored by the half it belongs to.
- CompatibilityHow Muzzle Devices Work (3D)Watch one shot leave an AR-15 muzzle in slow motion 3D through a bare barrel, a flash hider, a compensator, a muzzle brake and a linear comp. See where each sends the gas, and what that does to flash, recoil, muzzle rise and the blast beside you.
- CompatibilityBuffer Tube and Stock (3D)See an AR-15 buffer tube, end plate, castle nut and stock go on in 3D, walk the stock through its six positions, and put a mil spec and a commercial tube side by side to see why a stock only fits one of them.
- CompatibilityHow a Charging Handle Works (3D)Watch an AR-15 charging handle unlatch and pull the bolt carrier back by its gas key in 3D, then watch the rifle fire while the handle stays put. Compare a standard latch with an ambidextrous one.
- CompatibilityFree Float vs Drop In Handguard (3D)Watch an AR-15 free float handguard go on its barrel nut in 3D, lean on a free float and a drop in handguard to see which one moves the barrel, and lock an M-LOK rail section in. Plus M-LOK vs KeyMod and what length fits your barrel.
- CompatibilityHow Triggers Work (3D)Watch a standard trigger, a forced reset trigger and a binary trigger run inside an x-ray AR-15 in slow motion 3D. See the hammer, the disconnector, the FRT's locking bar and the bolt carrier at every step, and what each one needs and where it is legal.
- CompatibilityFRT and Binary Trigger PickerChoose your platform and see every forced reset trigger, binary trigger and Super Safety the catalog carries for it, what the host needs to run one, and where each is in stock.
- CompatibilityGlock Red Dot Fit CheckerPick how your Glock slide is cut and see which red dots mount directly, which need a plate, and the plates and optics in stock right now.
- CompatibilityGlock Size ComparisonPick any two Glocks and see them to scale as real photos sized to Glock's published dimensions, side by side, from behind and as an X-ray, with the difference in length, height, width and weight in one line and the pistols in stock for each.
- CompatibilityP385 Size ComparisonSee the SIG P385 CARRY, COMP and FULL to scale against the P365-XMACRO, the P320 and the Glock 19, 17, 45 and 43X, as real photos sized to the published length and height, with every dimension and where to order one.
- Paint plannerGun Paint PlannerRattle can guns online before you spray. Paint, stencil and camo a real photo of about 1,800 guns: AR-15s, AR-10s, AR-9s, AKs, every Glock, pistols, shotguns and bolt action rifles, the way the rattlecanned guns on r/rattlecannedguns are done, with Krylon, Rust-Oleum, Aluma-Hyde, DuraCoat and Cerakote colors, then get the cans to buy in spray order.
- TuningTwist Rate CalculatorPick a bullet and a twist rate, get the Miller stability factor, then see barrels with that twist and ammo loaded with that bullet, with today's price per round.
- TuningOptic Zero (3D)See where a 25, 36, 50, 100 or 200 yard zero hits on a 3D range, with your ammo, barrel length and optic height. Compare two zeros side by side, look through your red dot, EOTech or LPVO at each distance, then tap where your group hit and get the exact clicks up, down, left and right for your optic.
- LegalBarrel and Overall Length CheckerEnter barrel length, muzzle device and how the back end is configured, and see whether the build is a rifle, a short barreled rifle, a pistol or an AOW under federal law, with the barrels in stock at that length.
- LegalSBR Planner (3D)Set the barrel anywhere from 7.5 to 16 inches, put a stock, a brace or a folder on the back, pin a muzzle device or slide on a can. The ruler under the rifle shows whether you've cleared the 16 inch barrel line and the 26 inch overall line. Pick your state for its SBR, suppressor and assault weapon rules, then price every part and open the build in one click.
- PlanningNight VisionLook around a real 360 degree scene through Gen 1, Gen 2+, Gen 3 green and white phosphor tubes, digital night vision and thermal. Turn the moon down from full to overcast, switch on an IR light, compare two devices side by side. Or walk a 3D farm at night and spot the people, hogs and deer hiding in it. Then see the PVS-14, PVS-31, GPNVG-18 and the thermal scopes people buy, with prices.
- Planning300 BLK vs 5.56 Race (3D)Race a 9 inch .300 Blackout against a 10.3 inch 5.56, or up to four rifles of your own, down a 3D range. Every rifle fires at once in slow motion, and you get each one's time, speed, energy and drop at 100 to 500 yards.
- CompatibilityCo-Witness Checker (3D)Put a micro red dot, a full size dot or an EOTech on an AR-15 at 1.41, 1.535, 1.57, 1.93 or 2.26 inches and see where your iron sights land in the window, in 3D: absolute, lower 1/3, or under the window.
- PlanningAmmo Cutaway (3D)Cut M193, M855 green tip, M855A1, 77 gr OTM and .300 BLK supersonic and subsonic in half and compare them side by side in 3D: what each bullet is made of, its speed from short barrels, steel targets, and today's price per round. Then watch a .300 BLK round go into a 5.56 chamber.
- TuningWill It Eat Cheap Ammo? (3D)Pick your ammo and your AR-15: barrel and gas length, gas block, buffer, chamber, extractor and how clean it is. See if it will cycle and extract cheap steel case or bulk .223, which part is the weak link on a real 3D rifle, and try each fix to watch the answer change.
- PlanningAstigmatism Optic Test (3D)See a red dot, a circle dot, an EOTech, a prism and an LPVO through eyes with astigmatism, on a 3D AR-15. Pick how strong it is, the light, which way your dot smears and the brightness, and every optic is ranked for those eyes.
- PlanningOptics Without Power (3D)Cut the power to a red dot, an EOTech, a prism, an LPVO or an ACOG on a 3D AR-15 and see what's left in the window, by day and at night, with or without backup iron sights. For a dead battery, a cold morning or an EMP.
- TuningMechanical Offset (3D)See how far under the dot an AR-15 hits at 3 to 25 yards, in 3D: pick your optic height, zero and caliber, and the view through the optic shows the hole under the dot on a 3x5 card, with the hold for every distance.
- CompatibilityCaliber Conversion (3D)Convert a 5.56 AR-15 to .300 Blackout, 6.5 Grendel, 6mm ARC, .224 Valkyrie, 7.62x39, .350 Legend, .450 Bushmaster, 9mm or .22 LR and see on a real 3D rifle which parts you swap: the barrel, the bolt, the magazines, the buffer, and what stays the same.
- Compatibility5.56 vs .223 Chamber (3D)See a .223 Remington, a 5.56 NATO and a .223 Wylde chamber cut in half in 3D, with a round seated in each. Pick your chamber and your ammo to see where the bullet meets the rifling, why 5.56 in a .223 chamber is unsafe, and why Wylde takes both.
- CompatibilityChrome vs Nitride vs Stainless (3D)See a chrome lined, a nitrided and a stainless 5.56 barrel cut in half at the throat in 3D, then wear them from new to shot out. Compare what each finish is, how long it lasts, how it shoots, and which to buy for your rifle.
- TuningClear AR-15 Jams (3D)See seven AR-15 jams inside a see through receiver in 3D, from a click with no bang to a stovepipe, a double feed, a stuck case and a bolt override, and step through clearing each one. Learn when tap, rack works and when it doesn't.
- TuningTwist Rate and Keyholing (3D)What does 1:7 twist mean, and why does it matter? Fire a bullet down a rifled barrel in 3D and watch it spin, fly and hit the paper. Pick 55, 62 or 77 grain, a 1:7, 1:8, 1:9 or 1:12 barrel, the distance and the air temperature, and see a stable round hole, a wobbling bullet or a keyhole.
- TuningSuppressor Types (3D)How does a suppressor work inside? Cut a can in half in 3D and fire one shot through a cone baffle stack, a one piece monocore and a flow-through can. Watch the gas swirl, zigzag or run straight out the front, see how much comes back at your face, and where the brass lands on a 16 inch carbine or an 11.5 inch SBR.
- TuningGas Block vs Buffer (3D)Can on and brass at 1 o'clock: turn the gas down or add buffer weight? Turn an adjustable gas block's screw in 3D and watch less gas reach the bolt carrier, or step from H to H2 and H3 and watch the same gas push more weight. See where the brass lands, the carrier speed, the gas at your face and when it short strokes.
- AmmoBallistic Gel (3D)Fire M193, M855, 77 gr OTM, .300 Blackout 110 gr TAC-TX or 220 gr subsonic into a block of ballistic gel in 3D, from a 10.3 to 20 inch barrel at 10 to 300 yards. Watch the bullet yaw, break up or open in slow motion, see the stretch cavity and the wound it leaves, how deep it goes against the FBI's 12 to 18 inches, and how far out your barrel keeps 5.56 fast enough to fragment.



