Chrome Lined vs Nitride vs Stainless Barrel in 3D: Throat Wear Compared
See a chrome lined, a nitrided and a stainless 5.56 barrel cut in half at the throat in 3D, then wear them from new to shot out. Compare what each finish is, how long it lasts, how it shoots, and which to buy for your rifle.
Quick answer
- Chrome lining is a hard layer plated inside the bore. Nitriding (QPQ, Melonite) is not a coating: it hardens the steel's own surface, inside and out.
- Criterion says a chrome lined or nitrided barrel can last double or even triple an untreated barrel. The throat wears first, and the bullet jumps farther as it does.
- Bare 416R stainless is the usual match barrel steel. Criterion and Shooting Illustrated put nitrided barrels on par with it for accuracy.
Source: Criterion Barrels, Faxon Firearms, Shooting Illustrated and Gun Digest on barrel finishes.
See chrome lined, nitride and stainless barrels in 3D
The same 5.56 barrel three ways, cut in half at the throat. Pick what the rifle is for, or a finish, then wear the barrels from new to shot out and watch where the rifling starts.
Nitride 5.56 barrel, well used
cut at the throat · spread 6x
The same 5.56 NATO barrel three ways, each cut in half at the throat with an M855 seated. The chrome lining (pale) and the nitrided surface (blue) are drawn far thicker than they are so they show, and the throat is spread 6x across. Wear is drawn, not measured: as the throat erodes, the start of the rifling moves forward and the bullet jumps farther. The treated barrels wear at 0.4 of bare steel's rate here, from Criterion's "double or even triple" the life.
Salt bath nitrided 4150 CMV
Nitride
Not a coating: salt bath nitriding (QPQ, Melonite) diffuses nitrogen into the steel's surface, hardening it inside the bore and outside the barrel, without changing its dimensions.
In the drawing its throat wears at 40% of bare stainless steel's rate.
- Inside the bore
- Hardened steel surface, nothing added
- Outside
- Hardened and black, same treatment
- Heat and hard use
- Holds up well in semi auto. Criterion puts treated barrels, chrome or nitride, at double or triple an untreated barrel's life.
| Finish | Inside | Heat and hard use | Wet weather | Accuracy |
|---|---|---|---|---|
| Hard chrome plated on | Best. Faxon notes chrome lining began on machine guns and says a chrome bore resists throat erosion under sustained full auto fire better than the other common finishes. | The bore is well protected; the phosphate outside protects less than nitride does (Criterion). | Plating can go on unevenly, which is where chrome's old reputation comes from. Criterion and Gun Digest say a good modern chrome barrel shoots under 1 MOA. | |
| Hardened steel surface, nothing added | Holds up well in semi auto. Criterion puts treated barrels, chrome or nitride, at double or triple an untreated barrel's life. | Best of the three: the same treatment covers the bore and the outside. | Criterion and Shooting Illustrated's test put nitrided barrels on par with untreated match stainless. | |
| Bare steel | Wears fastest of the three when it's run hot: its throat has no hard layer. | Resists rust better than plain carbon steel, but it's not rustproof. | The match barrel steel: bare, so nothing sits between the rifling and the bullet. |
What's the difference between chrome lined, nitride and stainless?
What is in the bore. A chrome lined barrel has a thin layer of hard chrome plated onto the inside of the chamber and bore, over 4150 chrome moly vanadium steel; it's the lining on military M4 and M16 barrels. A nitrided barrel (salt bath nitride, sold as QPQ or Melonite) has nothing added: nitrogen is diffused into the steel's surface, which hardens it inside the bore and outside the barrel without changing its dimensions, as Shooting Illustrated and Gun Digest describe it. A stainless barrel is usually bare 416R with no lining or treatment in the bore.
Which barrel lasts longest?
A treated one, chrome or nitride. Criterion Barrels says either can give double or even triple the life of an untreated barrel. Under sustained heat, like strings of rapid or full auto fire, Faxon says chrome holds the throat together best, which is why it went on machine guns first. Bare stainless wears fastest of the three when it's run hot.
Barrels wear at the throat first. Hot gas and bullets erode the start of the rifling, which moves it forward, so the bullet jumps farther before it engages and groups open up (Criterion). How fast depends on the load, the rate of fire and the heat, and nobody publishes one number for it; Gun Digest notes there's no study that proves chrome doubles a barrel's life. That is why the 3D view draws wear rather than measuring it.
Is a chrome lined barrel less accurate?
Not by much, if it's made well. Chrome's old reputation comes from plating going on unevenly, and a match shooter will still pick bare stainless. Criterion and Gun Digest say a good modern chrome lined barrel shoots under 1 MOA, and Criterion and Shooting Illustrated's test put nitrided barrels on par with untreated match stainless. For how the chamber behind the throat changes accuracy, see 5.56 vs .223 chamber, and for twist, the twist rate calculator.
Which barrel finish should I buy?
Nitride, for most rifles. It lasts, it protects the bore and the outside from rust, and it shoots as well as match stainless for less. Pick chrome lined if the rifle will be run hot and hard, the way the military runs it: the outside of a chrome barrel is usually phosphate, which protects less than nitride does (Criterion). Pick stainless for pure precision, and plan on a new barrel sooner.
Barrels in stock by finish
Read off each listing's name, ranked by what builders add most. One listing per model.
Chrome lined
Ranked by what builders add most, in stock first. One listing per model.






Nitride
Ranked by what builders add most, in stock first. One listing per model.






Stainless
Ranked by what builders add most, in stock first. One listing per model.






Frequently Asked Questions
Is nitride better than chrome lined?
For most rifles, yes. Nitride hardens the bore and the outside of the barrel, so it resists rust better, and Criterion and Shooting Illustrated put it on par with match stainless for accuracy. Chrome lining still holds the throat together best under sustained full auto heat, Faxon says.
Does a chrome lined barrel last longer?
Than bare steel, yes. Criterion says a chrome lined or nitrided barrel can last double or even triple an untreated one. Between chrome and nitride the gap is small in semi auto; chrome pulls ahead when the barrel is run very hot.
Are chrome lined barrels less accurate?
Slightly, at most. Chrome plating can go on unevenly, which is where the reputation comes from, but Criterion and Gun Digest say a good modern chrome lined barrel shoots under 1 MOA.
Is a stainless barrel better?
For precision, yes. Most match barrels are bare 416R stainless, lapped smooth, with nothing between the rifling and the bullet. Its throat has no hard layer, so it wears fastest when run hot, and it can still rust.
What is a nitride barrel?
A steel barrel hardened by salt bath nitriding, sold as QPQ or Melonite. It's not a coating: nitrogen is diffused into the surface inside and out, which hardens it without changing the barrel's dimensions.
Where does a barrel wear out first?
At the throat. Hot gas and bullets erode the start of the rifling, which moves it forward, so the bullet jumps farther before it engages and groups open up.
Cite this tool: GunPartPicker, “Chrome Lined vs Nitride vs Stainless Barrel in 3D: Throat Wear Compared”, https://gunpartpicker.net/tools/chrome-vs-nitride-vs-stainless-barrel. Finish claims from Criterion Barrels, Faxon Firearms, Shooting Illustrated and Gun Digest; throat from the 5.56 NATO reamer print; wear drawn for illustration; barrels confirmed in stock today Free to cite with attribution.
Read next
All guides →More Gun Tools
- Compatibility5.56 vs .223 Chamber (3D)See a .223 Remington, a 5.56 NATO and a .223 Wylde chamber cut in half in 3D, with a round seated in each. Pick your chamber and your ammo to see where the bullet meets the rifling, why 5.56 in a .223 chamber is unsafe, and why Wylde takes both.
- TuningTwist Rate CalculatorPick a bullet and a twist rate, get the Miller stability factor, then see barrels with that twist and ammo loaded with that bullet, with today's price per round.
- LegalBarrel and Overall Length CheckerEnter barrel length, muzzle device and how the back end is configured, and see whether the build is a rifle, a short barreled rifle, a pistol or an AOW under federal law, with the barrels in stock at that length.
- LegalGun Travel CheckerCan I bring my gun to another state? Pick where you start, where you are going and what is coming along: carry pistol, AR-15, magazines, suppressor, SBR, brace, forced reset or binary trigger, hollow points. Every state on the route is checked for transporting firearms across state lines: magazine limits, assault weapon bans, NFA rules, carry permit type and trigger bans, with what to do before the state line.
- PlanningAR Build Cost CalculatorHow much does it cost to build an AR-15? Pick caliber, barrel length, stock or brace and optic, then drag both edges of the price band from the cheap end to the top end. Every slot fills with the part builders add most that is in stock, priced live. The headline total is the core rifle, optics and extras are priced separately, and beside them sits what builders really pay per slot, measured from real part picks. Roll a random build, or open yours in the builder in one click. Computed from over 1 million AR parts selected on GunPartPicker since 2020.
- CompatibilityMuzzle Thread CheckerPick your barrel's caliber and platform, get the standard thread pitch, and see every muzzle device and suppressor in the catalog that actually threads on, with live prices.
- CompatibilitySuppressor Mounts (3D)Put a can on its mount in 3D. Compare SilencerCo ASR, Dead Air KeyMo, SureFire Fast-Attach, HUXWRX QD, Plan B, HUB 1.375x24 and direct thread: what goes on the barrel, what is on the can, how it locks and which cans fit which mounts. Cut it open to see the taper and the baffles, then shop the mounts and cans in stock.
- CompatibilityDI vs Piston (3D)Watch a direct impingement AR-15 and a gas piston HK416 fire in slow motion x-ray 3D. Follow the gas from the port back into the carrier, or into a piston that kicks an op rod, see which bolt runs hot, and compare weight, cleaning, suppressed use, carrier tilt and cost.
- CompatibilityUpper vs Lower Receiver (3D)Take a real AR-15 apart in 3D and see how the upper and lower receiver go together. Push the takedown pin, hinge the upper open on the pivot pin, pull the bolt carrier group and lift the upper off, with every part colored by the half it belongs to.
- CompatibilityHow Muzzle Devices Work (3D)Watch one shot leave an AR-15 muzzle in slow motion 3D through a bare barrel, a flash hider, a compensator, a muzzle brake and a linear comp. See where each sends the gas, and what that does to flash, recoil, muzzle rise and the blast beside you.
- CompatibilityHow a BCG Works (3D)Watch an AR-15 bolt carrier group unlock, extract and lock again in slow motion 3D, then take it apart part by part. See the cam pin turn the bolt out of the barrel extension, and what each part does.
- CompatibilityBuffer Tube and Stock (3D)See an AR-15 buffer tube, end plate, castle nut and stock go on in 3D, walk the stock through its six positions, and put a mil spec and a commercial tube side by side to see why a stock only fits one of them.
- CompatibilityHow a Charging Handle Works (3D)Watch an AR-15 charging handle unlatch and pull the bolt carrier back by its gas key in 3D, then watch the rifle fire while the handle stays put. Compare a standard latch with an ambidextrous one.
- CompatibilityHow the Gas System Works (3D)Watch a shot's gas go up an AR-15's gas port, through the gas block and back down the gas tube to the bolt carrier in slow motion 3D. Turn it down with an adjustable gas block, and see where the port sits on pistol, carbine, mid length and rifle gas.
- CompatibilityFree Float vs Drop In Handguard (3D)Watch an AR-15 free float handguard go on its barrel nut in 3D, lean on a free float and a drop in handguard to see which one moves the barrel, and lock an M-LOK rail section in. Plus M-LOK vs KeyMod and what length fits your barrel.
- CompatibilityHow Triggers Work (3D)Watch a standard trigger, a forced reset trigger and a binary trigger run inside an x-ray AR-15 in slow motion 3D. See the hammer, the disconnector, the FRT's locking bar and the bolt carrier at every step, and what each one needs and where it is legal.
- CompatibilityFRT and Binary Trigger PickerChoose your platform and see every forced reset trigger, binary trigger and Super Safety the catalog carries for it, what the host needs to run one, and where each is in stock.
- CompatibilityGlock Red Dot Fit CheckerPick how your Glock slide is cut and see which red dots mount directly, which need a plate, and the plates and optics in stock right now.
- CompatibilityGlock Size ComparisonPick any two Glocks and see them to scale as real photos sized to Glock's published dimensions, side by side, from behind and as an X-ray, with the difference in length, height, width and weight in one line and the pistols in stock for each.
- CompatibilityP385 Size ComparisonSee the SIG P385 CARRY, COMP and FULL to scale against the P365-XMACRO, the P320 and the Glock 19, 17, 45 and 43X, as real photos sized to the published length and height, with every dimension and where to order one.
- Paint plannerGun Paint PlannerRattle can guns online before you spray. Paint, stencil and camo a real photo of about 1,800 guns: AR-15s, AR-10s, AR-9s, AKs, every Glock, pistols, shotguns and bolt action rifles, the way the rattlecanned guns on r/rattlecannedguns are done, with Krylon, Rust-Oleum, Aluma-Hyde, DuraCoat and Cerakote colors, then get the cans to buy in spray order.
- TuningOptic Zero (3D)See where a 25, 36, 50, 100 or 200 yard zero hits on a 3D range, with your ammo, barrel length and optic height. Compare two zeros side by side, look through your red dot, EOTech or LPVO at each distance, then tap where your group hit and get the exact clicks up, down, left and right for your optic.
- TuningBuffer Weight CalculatorEnter your gas system, barrel length, buffer tube and ammo, add a suppressor or a fast trigger, and get the buffer weight to start with plus the buffers in stock that match.
- TuningBuffer System (3D)Watch an AR-15 cycle in slow motion, cut open: gas drives the bolt carrier back, the bolt unlocks and throws the brass, the buffer and spring soak it up and send it home. Swap carbine, H, H2 and H3 buffers, add gas or a suppressor, and see the carrier speed, where the brass lands and when it short strokes.
- LegalSBR Planner (3D)Set the barrel anywhere from 7.5 to 16 inches, put a stock, a brace or a folder on the back, pin a muzzle device or slide on a can. The ruler under the rifle shows whether you've cleared the 16 inch barrel line and the 26 inch overall line. Pick your state for its SBR, suppressor and assault weapon rules, then price every part and open the build in one click.
- PlanningNight VisionLook around a real 360 degree scene through Gen 1, Gen 2+, Gen 3 green and white phosphor tubes, digital night vision and thermal. Turn the moon down from full to overcast, switch on an IR light, compare two devices side by side. Or walk a 3D farm at night and spot the people, hogs and deer hiding in it. Then see the PVS-14, PVS-31, GPNVG-18 and the thermal scopes people buy, with prices.
- Planning300 BLK vs 5.56 Race (3D)Race a 9 inch .300 Blackout against a 10.3 inch 5.56, or up to four rifles of your own, down a 3D range. Every rifle fires at once in slow motion, and you get each one's time, speed, energy and drop at 100 to 500 yards.
- CompatibilityCo-Witness Checker (3D)Put a micro red dot, a full size dot or an EOTech on an AR-15 at 1.41, 1.535, 1.57, 1.93 or 2.26 inches and see where your iron sights land in the window, in 3D: absolute, lower 1/3, or under the window.
- PlanningAmmo Cutaway (3D)Cut M193, M855 green tip, M855A1, 77 gr OTM and .300 BLK supersonic and subsonic in half and compare them side by side in 3D: what each bullet is made of, its speed from short barrels, steel targets, and today's price per round. Then watch a .300 BLK round go into a 5.56 chamber.
- TuningWill It Eat Cheap Ammo? (3D)Pick your ammo and your AR-15: barrel and gas length, gas block, buffer, chamber, extractor and how clean it is. See if it will cycle and extract cheap steel case or bulk .223, which part is the weak link on a real 3D rifle, and try each fix to watch the answer change.
- PlanningAstigmatism Optic Test (3D)See a red dot, a circle dot, an EOTech, a prism and an LPVO through eyes with astigmatism, on a 3D AR-15. Pick how strong it is, the light, which way your dot smears and the brightness, and every optic is ranked for those eyes.
- PlanningOptics Without Power (3D)Cut the power to a red dot, an EOTech, a prism, an LPVO or an ACOG on a 3D AR-15 and see what's left in the window, by day and at night, with or without backup iron sights. For a dead battery, a cold morning or an EMP.
- TuningMechanical Offset (3D)See how far under the dot an AR-15 hits at 3 to 25 yards, in 3D: pick your optic height, zero and caliber, and the view through the optic shows the hole under the dot on a 3x5 card, with the hold for every distance.
- TuningEjection Pattern (3D)Tap where your brass lands and a real 3D AR-15 throws it there and tells you if it's overgassed, tuned or short on gas. Or set up your rifle (barrel and gas length, buffer, spring, gas block, suppressor, ammo) and watch where the brass goes, then try each fix and see it move.
- CompatibilityCaliber Conversion (3D)Convert a 5.56 AR-15 to .300 Blackout, 6.5 Grendel, 6mm ARC, .224 Valkyrie, 7.62x39, .350 Legend, .450 Bushmaster, 9mm or .22 LR and see on a real 3D rifle which parts you swap: the barrel, the bolt, the magazines, the buffer, and what stays the same.
- TuningClear AR-15 Jams (3D)See seven AR-15 jams inside a see through receiver in 3D, from a click with no bang to a stovepipe, a double feed, a stuck case and a bolt override, and step through clearing each one. Learn when tap, rack works and when it doesn't.
- TuningTwist Rate and Keyholing (3D)What does 1:7 twist mean, and why does it matter? Fire a bullet down a rifled barrel in 3D and watch it spin, fly and hit the paper. Pick 55, 62 or 77 grain, a 1:7, 1:8, 1:9 or 1:12 barrel, the distance and the air temperature, and see a stable round hole, a wobbling bullet or a keyhole.
- TuningSuppressor Types (3D)How does a suppressor work inside? Cut a can in half in 3D and fire one shot through a cone baffle stack, a one piece monocore and a flow-through can. Watch the gas swirl, zigzag or run straight out the front, see how much comes back at your face, and where the brass lands on a 16 inch carbine or an 11.5 inch SBR.
- TuningGas Block vs Buffer (3D)Can on and brass at 1 o'clock: turn the gas down or add buffer weight? Turn an adjustable gas block's screw in 3D and watch less gas reach the bolt carrier, or step from H to H2 and H3 and watch the same gas push more weight. See where the brass lands, the carrier speed, the gas at your face and when it short strokes.
- AmmoBallistic Gel (3D)Fire M193, M855, 77 gr OTM, .300 Blackout 110 gr TAC-TX or 220 gr subsonic into a block of ballistic gel in 3D, from a 10.3 to 20 inch barrel at 10 to 300 yards. Watch the bullet yaw, break up or open in slow motion, see the stretch cavity and the wound it leaves, how deep it goes against the FBI's 12 to 18 inches, and how far out your barrel keeps 5.56 fast enough to fragment.

