How to Clear AR-15 Malfunctions, in 3D: Stovepipe, Double Feed, Bolt Override
See seven AR-15 jams inside a see through receiver in 3D, from a click with no bang to a stovepipe, a double feed, a stuck case and a bolt override, and step through clearing each one. Learn when tap, rack works and when it doesn't.
Quick answer
- Most AR-15 jams fall into a few kinds: a round that doesn't fire, a squib, a stovepipe, a double feed, a stuck case and a bolt override.
- A click with no bang is cleared on the spot: tap the magazine, rack the charging handle, reassess. A pop with weak recoil is the one time not to.
- Double feeds, stuck cases and bolt overrides take the magazine out first, and the rifle off the line to clear.
Source: the standard immediate and remedial action drills taught for the AR-15 and M4.
See each AR-15 jam in 3D, and clear it step by step
Pick a jam to see what it looks like inside the receiver, then step through the clear. The part causing it glows orange.
Stovepipe
step 1 of 4 · Stovepipe
An M4 seen from the ejection port side, with the receiver, barrel and magazine see through and the dust cover open. The part causing the jam glows orange; red is the wrong way to clear it. Always treat the rifle as loaded: muzzle in a safe direction, finger off the trigger.
Stovepipe · step 1 of 4
Stovepipe
The empty case is pinched between the bolt and the edge of the port.
- What you'll notice
- An empty case sticks straight up out of the ejection port, caught by the bolt.
- What's happening
- The case didn't clear the port before the bolt came forward: too little gas (a short stroke), a weak ejector spring, or a limp grip.
- Take the rifle off the line
- Repeated stovepipes point at the gas: check the gas block and tube, or try a lighter buffer or a stiffer load.
What is tap, rack, reassess?
The first thing to do when an AR-15 goes click instead of bang. Tap the bottom of the magazine to make sure it's seated, rack the charging handle all the way back and let it go to chamber a fresh round, then reassess: get back on target and decide whether to fire. Trainers call this immediate action, and it clears the most common stoppages without taking the rifle off your shoulder.
It isn't for everything. After a pop with weak recoil, a bullet may be stuck in the barrel, and racking a fresh round in behind it is how barrels burst. And if tap, rack doesn't clear it, or you can see brass jammed in the port, it's a remedial action jam: magazine out first, then clear it as the steps above show.
Why does my AR-15 keep jamming?
Most of the time it's the magazine. Worn or bent feed lips and weak springs cause double feeds and bolt overrides, so number your magazines and retire the one that keeps showing up. After that come gas, the extractor and ammo:
- Too little gas (a short stroke) leaves stovepipes and failures to lock back: check the gas block is lined up and tight, and that the buffer isn't too heavy for the gas. The buffer weight calculator and the gas system tool show how they balance.
- A tired extractor or its spring lets go of the rim, which leaves stuck cases and double feeds. See how the extractor pulls the case on the bolt carrier group tool.
- Ammo: squibs and duds are ammo, and steel cased rounds stick in hot or dirty chambers more than brass.
- A dry or filthy bolt carrier group slows the whole cycle. Run it wet.
Every jam at a glance
| Jam | What you'll notice | How to clear it |
|---|---|---|
| Click, no bang | You press the trigger and hear a click, but the rifle doesn't fire. | Tap the magazine, Rack it all the way, Let it go and reassess. |
| Pop and weak recoil (squib) | A pop that's quieter than a normal shot, with less recoil, and maybe no empty case thrown. | Unload, Check the barrel. Never tap and rack after a pop. A fresh round fired into a stuck bullet can bulge or burst the barrel. |
| Stovepipe | An empty case sticks straight up out of the ejection port, caught by the bolt. | Magazine out, Pluck the case, Magazine in, rack. |
| Double feed | The bolt stops partway forward; two rounds, or a round and an empty case, are fighting for the chamber. | Lock the bolt back, Strip the magazine, Rack three times, Fresh magazine, rack. |
| Stuck empty case | The bolt comes back but the chamber isn't empty: a fired case is stuck in it, often with a torn rim. | Magazine out, bolt locked back, Knock it out with a rod. |
| Stuck live round | The bolt is back but a live round is still in the chamber, and racking won't pull it. | Never rod it from the muzzle, Pull the carrier, Pry it out from the breech. Never push a live round out with a rod from the muzzle: the rod can strike the primer and fire it. |
| Bolt override | The bolt is stuck partway back, and a round is jammed on top of the bolt carrier, under the charging handle. | Magazine out, Hold the handle back, A tool holds the bolt, Slam the handle forward, Tip it out and reload. |
Bolt carrier groups in stock
A worn extractor is behind most stuck cases and many double feeds. Ranked by what builders add most, in stock first. One listing per model.
Ranked by what builders add most, in stock first. One listing per model.






Frequently Asked Questions
How do you clear a jammed AR-15?
Start with tap, rack, reassess: slap the magazine up, rack the charging handle all the way back, let it go and get back on target. If that doesn't clear it, or you can see brass jammed in the port, take the magazine out first, then clear the jam by type.
How do you fix a double feed on an AR-15?
Lock the bolt back, strip the magazine out, then rack the charging handle hard about three times to pull the case out of the chamber. Seat a fresh magazine and rack a round in.
What causes a stovepipe in an AR-15?
Usually too little gas: the bolt doesn't travel far enough back to throw the case clear, so it catches the case in the port. A misaligned gas block, a heavy buffer for the gas, weak ammo or a weak ejector spring are the usual reasons.
What is a bolt override?
A jam where a round pops up over the bolt and wedges it between the bolt carrier and the charging handle. It's usually a bad magazine. Clear it with the magazine out, the charging handle held back, a tool up through the magazine well to hold the bolt, then slam the handle forward to knock the round loose.
Should you tap and rack after a squib?
No. A quiet pop with weak recoil can mean the bullet is stuck in the barrel, and firing another round into it can bulge or burst the barrel. Unload and check the bore first.
How do you get a stuck live round out of an AR-15?
From the breech, never the muzzle. Take the bolt carrier group out and work the round out from the back with a brass rod or pick. A rod pushed down the barrel from the muzzle can set off the primer.
Cite this tool: GunPartPicker, “How to Clear AR-15 Malfunctions, in 3D: Stovepipe, Double Feed, Bolt Override”, https://gunpartpicker.net/tools/how-to-clear-ar-15-malfunctions. Clearing steps are the standard immediate and remedial action drills for the AR-15 and M4; bolt carrier groups confirmed in stock today Free to cite with attribution.
Read next
All guides →More Gun Tools
- CompatibilityHow a BCG Works (3D)Watch an AR-15 bolt carrier group unlock, extract and lock again in slow motion 3D, then take it apart part by part. See the cam pin turn the bolt out of the barrel extension, and what each part does.
- TuningBuffer Weight CalculatorEnter your gas system, barrel length, buffer tube and ammo, add a suppressor or a fast trigger, and get the buffer weight to start with plus the buffers in stock that match.
- CompatibilityHow the Gas System Works (3D)Watch a shot's gas go up an AR-15's gas port, through the gas block and back down the gas tube to the bolt carrier in slow motion 3D. Turn it down with an adjustable gas block, and see where the port sits on pistol, carbine, mid length and rifle gas.
- LegalGun Travel CheckerCan I bring my gun to another state? Pick where you start, where you are going and what is coming along: carry pistol, AR-15, magazines, suppressor, SBR, brace, forced reset or binary trigger, hollow points. Every state on the route is checked for transporting firearms across state lines: magazine limits, assault weapon bans, NFA rules, carry permit type and trigger bans, with what to do before the state line.
- PlanningAR Build Cost CalculatorHow much does it cost to build an AR-15? Pick caliber, barrel length, stock or brace and optic, then drag both edges of the price band from the cheap end to the top end. Every slot fills with the part builders add most that is in stock, priced live. The headline total is the core rifle, optics and extras are priced separately, and beside them sits what builders really pay per slot, measured from real part picks. Roll a random build, or open yours in the builder in one click. Computed from over 1 million AR parts selected on GunPartPicker since 2020.
- CompatibilityMuzzle Thread CheckerPick your barrel's caliber and platform, get the standard thread pitch, and see every muzzle device and suppressor in the catalog that actually threads on, with live prices.
- CompatibilitySuppressor Mounts (3D)Put a can on its mount in 3D. Compare SilencerCo ASR, Dead Air KeyMo, SureFire Fast-Attach, HUXWRX QD, Plan B, HUB 1.375x24 and direct thread: what goes on the barrel, what is on the can, how it locks and which cans fit which mounts. Cut it open to see the taper and the baffles, then shop the mounts and cans in stock.
- CompatibilityDI vs Piston (3D)Watch a direct impingement AR-15 and a gas piston HK416 fire in slow motion x-ray 3D. Follow the gas from the port back into the carrier, or into a piston that kicks an op rod, see which bolt runs hot, and compare weight, cleaning, suppressed use, carrier tilt and cost.
- CompatibilityUpper vs Lower Receiver (3D)Take a real AR-15 apart in 3D and see how the upper and lower receiver go together. Push the takedown pin, hinge the upper open on the pivot pin, pull the bolt carrier group and lift the upper off, with every part colored by the half it belongs to.
- CompatibilityHow Muzzle Devices Work (3D)Watch one shot leave an AR-15 muzzle in slow motion 3D through a bare barrel, a flash hider, a compensator, a muzzle brake and a linear comp. See where each sends the gas, and what that does to flash, recoil, muzzle rise and the blast beside you.
- CompatibilityBuffer Tube and Stock (3D)See an AR-15 buffer tube, end plate, castle nut and stock go on in 3D, walk the stock through its six positions, and put a mil spec and a commercial tube side by side to see why a stock only fits one of them.
- CompatibilityHow a Charging Handle Works (3D)Watch an AR-15 charging handle unlatch and pull the bolt carrier back by its gas key in 3D, then watch the rifle fire while the handle stays put. Compare a standard latch with an ambidextrous one.
- CompatibilityFree Float vs Drop In Handguard (3D)Watch an AR-15 free float handguard go on its barrel nut in 3D, lean on a free float and a drop in handguard to see which one moves the barrel, and lock an M-LOK rail section in. Plus M-LOK vs KeyMod and what length fits your barrel.
- CompatibilityHow Triggers Work (3D)Watch a standard trigger, a forced reset trigger and a binary trigger run inside an x-ray AR-15 in slow motion 3D. See the hammer, the disconnector, the FRT's locking bar and the bolt carrier at every step, and what each one needs and where it is legal.
- CompatibilityFRT and Binary Trigger PickerChoose your platform and see every forced reset trigger, binary trigger and Super Safety the catalog carries for it, what the host needs to run one, and where each is in stock.
- CompatibilityGlock Red Dot Fit CheckerPick how your Glock slide is cut and see which red dots mount directly, which need a plate, and the plates and optics in stock right now.
- CompatibilityGlock Size ComparisonPick any two Glocks and see them to scale as real photos sized to Glock's published dimensions, side by side, from behind and as an X-ray, with the difference in length, height, width and weight in one line and the pistols in stock for each.
- CompatibilityP385 Size ComparisonSee the SIG P385 CARRY, COMP and FULL to scale against the P365-XMACRO, the P320 and the Glock 19, 17, 45 and 43X, as real photos sized to the published length and height, with every dimension and where to order one.
- Paint plannerGun Paint PlannerRattle can guns online before you spray. Paint, stencil and camo a real photo of about 1,800 guns: AR-15s, AR-10s, AR-9s, AKs, every Glock, pistols, shotguns and bolt action rifles, the way the rattlecanned guns on r/rattlecannedguns are done, with Krylon, Rust-Oleum, Aluma-Hyde, DuraCoat and Cerakote colors, then get the cans to buy in spray order.
- TuningTwist Rate CalculatorPick a bullet and a twist rate, get the Miller stability factor, then see barrels with that twist and ammo loaded with that bullet, with today's price per round.
- TuningOptic Zero (3D)See where a 25, 36, 50, 100 or 200 yard zero hits on a 3D range, with your ammo, barrel length and optic height. Compare two zeros side by side, look through your red dot, EOTech or LPVO at each distance, then tap where your group hit and get the exact clicks up, down, left and right for your optic.
- TuningBuffer System (3D)Watch an AR-15 cycle in slow motion, cut open: gas drives the bolt carrier back, the bolt unlocks and throws the brass, the buffer and spring soak it up and send it home. Swap carbine, H, H2 and H3 buffers, add gas or a suppressor, and see the carrier speed, where the brass lands and when it short strokes.
- LegalBarrel and Overall Length CheckerEnter barrel length, muzzle device and how the back end is configured, and see whether the build is a rifle, a short barreled rifle, a pistol or an AOW under federal law, with the barrels in stock at that length.
- LegalSBR Planner (3D)Set the barrel anywhere from 7.5 to 16 inches, put a stock, a brace or a folder on the back, pin a muzzle device or slide on a can. The ruler under the rifle shows whether you've cleared the 16 inch barrel line and the 26 inch overall line. Pick your state for its SBR, suppressor and assault weapon rules, then price every part and open the build in one click.
- PlanningNight VisionLook around a real 360 degree scene through Gen 1, Gen 2+, Gen 3 green and white phosphor tubes, digital night vision and thermal. Turn the moon down from full to overcast, switch on an IR light, compare two devices side by side. Or walk a 3D farm at night and spot the people, hogs and deer hiding in it. Then see the PVS-14, PVS-31, GPNVG-18 and the thermal scopes people buy, with prices.
- Planning300 BLK vs 5.56 Race (3D)Race a 9 inch .300 Blackout against a 10.3 inch 5.56, or up to four rifles of your own, down a 3D range. Every rifle fires at once in slow motion, and you get each one's time, speed, energy and drop at 100 to 500 yards.
- CompatibilityCo-Witness Checker (3D)Put a micro red dot, a full size dot or an EOTech on an AR-15 at 1.41, 1.535, 1.57, 1.93 or 2.26 inches and see where your iron sights land in the window, in 3D: absolute, lower 1/3, or under the window.
- PlanningAmmo Cutaway (3D)Cut M193, M855 green tip, M855A1, 77 gr OTM and .300 BLK supersonic and subsonic in half and compare them side by side in 3D: what each bullet is made of, its speed from short barrels, steel targets, and today's price per round. Then watch a .300 BLK round go into a 5.56 chamber.
- TuningWill It Eat Cheap Ammo? (3D)Pick your ammo and your AR-15: barrel and gas length, gas block, buffer, chamber, extractor and how clean it is. See if it will cycle and extract cheap steel case or bulk .223, which part is the weak link on a real 3D rifle, and try each fix to watch the answer change.
- PlanningAstigmatism Optic Test (3D)See a red dot, a circle dot, an EOTech, a prism and an LPVO through eyes with astigmatism, on a 3D AR-15. Pick how strong it is, the light, which way your dot smears and the brightness, and every optic is ranked for those eyes.
- PlanningOptics Without Power (3D)Cut the power to a red dot, an EOTech, a prism, an LPVO or an ACOG on a 3D AR-15 and see what's left in the window, by day and at night, with or without backup iron sights. For a dead battery, a cold morning or an EMP.
- TuningMechanical Offset (3D)See how far under the dot an AR-15 hits at 3 to 25 yards, in 3D: pick your optic height, zero and caliber, and the view through the optic shows the hole under the dot on a 3x5 card, with the hold for every distance.
- TuningEjection Pattern (3D)Tap where your brass lands and a real 3D AR-15 throws it there and tells you if it's overgassed, tuned or short on gas. Or set up your rifle (barrel and gas length, buffer, spring, gas block, suppressor, ammo) and watch where the brass goes, then try each fix and see it move.
- CompatibilityCaliber Conversion (3D)Convert a 5.56 AR-15 to .300 Blackout, 6.5 Grendel, 6mm ARC, .224 Valkyrie, 7.62x39, .350 Legend, .450 Bushmaster, 9mm or .22 LR and see on a real 3D rifle which parts you swap: the barrel, the bolt, the magazines, the buffer, and what stays the same.
- Compatibility5.56 vs .223 Chamber (3D)See a .223 Remington, a 5.56 NATO and a .223 Wylde chamber cut in half in 3D, with a round seated in each. Pick your chamber and your ammo to see where the bullet meets the rifling, why 5.56 in a .223 chamber is unsafe, and why Wylde takes both.
- CompatibilityChrome vs Nitride vs Stainless (3D)See a chrome lined, a nitrided and a stainless 5.56 barrel cut in half at the throat in 3D, then wear them from new to shot out. Compare what each finish is, how long it lasts, how it shoots, and which to buy for your rifle.
- TuningTwist Rate and Keyholing (3D)What does 1:7 twist mean, and why does it matter? Fire a bullet down a rifled barrel in 3D and watch it spin, fly and hit the paper. Pick 55, 62 or 77 grain, a 1:7, 1:8, 1:9 or 1:12 barrel, the distance and the air temperature, and see a stable round hole, a wobbling bullet or a keyhole.
- TuningSuppressor Types (3D)How does a suppressor work inside? Cut a can in half in 3D and fire one shot through a cone baffle stack, a one piece monocore and a flow-through can. Watch the gas swirl, zigzag or run straight out the front, see how much comes back at your face, and where the brass lands on a 16 inch carbine or an 11.5 inch SBR.
- TuningGas Block vs Buffer (3D)Can on and brass at 1 o'clock: turn the gas down or add buffer weight? Turn an adjustable gas block's screw in 3D and watch less gas reach the bolt carrier, or step from H to H2 and H3 and watch the same gas push more weight. See where the brass lands, the carrier speed, the gas at your face and when it short strokes.
- AmmoBallistic Gel (3D)Fire M193, M855, 77 gr OTM, .300 Blackout 110 gr TAC-TX or 220 gr subsonic into a block of ballistic gel in 3D, from a 10.3 to 20 inch barrel at 10 to 300 yards. Watch the bullet yaw, break up or open in slow motion, see the stretch cavity and the wound it leaves, how deep it goes against the FBI's 12 to 18 inches, and how far out your barrel keeps 5.56 fast enough to fragment.
